JVC KD-SX997R Service Manual Download

Page: 21 / 55

KD-SX998R,KD-SX997R

(No.49819)1-21

2.2.17 Removing the gears

(See Figs.37 to 40)

• Prior to performing the following procedure, remove the top

cover, chassis unit, top plate assembly and pickup unit.

• Pull out the loading gear 3. (See Fig.35.)

(1) Pull out the feed gear.
(2) Move the loading plate assembly in the direction of the ar-

row to release the L side plate from the two slots m' of the
chassis rivet assembly. (See Fig.37.)

(3) Detach the loading plate assembly upward from the chas-

sis rivet assembly while releasing the joint

. Remove the

slide hook and loading plate spring from the loading plate
assembly.

(4) Pull out the loading gear 2 and remove the change lock le-

ver.

(5) Remove the E ring and washer attaching the change gear

(6) The change gear 2, change gear spring and adjusting

washer come off.

(7) Remove the loading gear 1.
(8) Move the change plate rivet assembly in the direction of the

arrow to release from the three shafts of the chassis rivet
assembly upward. (See Fig.38.)

(9) Detach the loading gear plate rivet assembly from the shaft

of the chassis rivet assembly upward while releasing the
joint

. (See Figs.38 and 40.)

(10) Pull out the loading gear 4.

Fig.37

Fig.38

Fig.39

Fig.40

Slot m'

Joint n'

Feed gear

Loading plate assembly

L side plate

Chassis rivet assembly

Joint p'

Loading gear 4

Loading gear 2

Loading gear 1

Change gear 2

Loading gear plate
rivet assembly

E ring

Shafts

Change plate
rivet assembly

Shaft

Chassis rivet assembly

Loading plate assembly

Loading plate spring

Chassis rivet assembly

Slot m'

Joint n'

L side plate

Slide hook

Loading gear 2

Loading gear 4

Change gear 2

Loading gear 1

E ring

Washer

Change gear

spring

Loading gear plate rivet

assembly

Chassis rivet assembly

Adjusting

washer

Change plate

rivet assembly

Change lock lever

Summary of Contents for KD-SX997R
























































Search results

Summary of Contents for KD-SX997R

Reviews:

Related manuals for KD-SX997R

Brands by name

Popular brands

JVC KD-SX997R, Service Manual

Search results

Summary of Contents for KD-SX997R

Reviews:

Related manuals for KD-SX997R

Brands by name

Popular brands