JVC KD-G701 Service Manual Download Page 18

Page: 18 / 65

1-18 (No.MA057B)

3.2.7 Removing the pickup unit

(See Figs.14 to 18)

• Prior to performing the following procedure, remove the top

cover, connector board and chassis unit.

(1) Remove the screw

and pull out the pu. shaft holder from

the pu. shaft.

(2) Remove the screw

attaching the feed sw. holder.

(3) Move the part

of the pickup unit upward with the pu. shaft

and the feed sw. holder, then release the joint f of the feed
sw. holder in the direction of the arrow. The joint

of the

pickup unit and the feed rack is released, and the feed sw.
holder comes off.

(4) Remove the pu. shaft from the pickup unit.
(5) Remove the screw

attaching the feed rack to the pickup

unit.

3.2.8 Reattaching the pickup unit

(See Figs.14 to 17)

(1) Reattach the feed rack to the pickup unit using the screw

(2) Reattach the feed sw. holder to the feed rack while setting

the joint g to the slot of the feed rack and setting the part f
of the feed rack to the switch of the feed sw. holder correct-
ly.

(3) As the feed sw. holder is temporarily attached to the pickup

unit, set to the gear of the joint g and to the bending part of
the chassis (joint

) at a time.

CAUTION:

Make sure that the part i on the underside of the feed
rack is certainly inserted to the slot j of the change lock
lever.

(4) Reattach the feed sw. holder using the screw

(5) Reattach the pu. shaft to the pickup unit. Reattach the pu.

shaft holder to the pu. shaft using the screw

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Feed sw. holder

Joint g

Joint f

Part e

Pickup unit

Pu. shaft holder

Pu. shaft

Feed sw. holder

Part e

Pickup unit

Feed rack

Feed sw.
holder

Joint f

Pu. shaft
holder

Pu. shaft

Pickup unit

Joint h

Part i

Slot j

Joint g

Feed rack

Pickup unit

Joint f

Joint g

Feed rack

Pickup unit

Feed sw. holder

Summary of Contents for KD-G701


































































Search results

Summary of Contents for KD-G701

Reviews:

Related manuals for KD-G701

Brands by name

Popular brands

JVC KD-G701, Service Manual

Search results

Summary of Contents for KD-G701

Reviews:

Related manuals for KD-G701

Brands by name

Popular brands