JVC KD-G701 Service Manual Download Page 8

Page: 8 / 65

1-8 (No.MA057B)

3.1.3 Removing the top chassis assembly

(See Figs.3 to 6)

• Prior to performing the following procedures, remove the heat

sink.

Reference:

Remove the front panel assembly as required.
(1) From the bottom side of the main body, remove the two

screws

attaching the top chassis assembly to the bottom

chassis assembly. (See Fig.3.)

(2) From the both and rear sides of the main body, remove the

four screws

attaching the top chassis assembly to the

bottom chassis assembly. (See Figs.4 to 6.)

(3) Lift the top chassis assembly in the direction of the arrow,

disconnect the connector

CN501

on the main board. (See

Figs.5 and 6.)

(4) Take out the top chassis assembly from the bottom chassis

assembly.

Fig.3

Fig.4

Fig.5

Fig.6

Top chassis assembly

Bottom chassis assembly

Top chassis assembly

Bottom chassis assembly

CD mechanism assembly

Main board

CN501

Top chassis assembly

Bottom chassis assembly

Summary of Contents for KD-G701


































































Search results

Summary of Contents for KD-G701

Reviews:

Related manuals for KD-G701

Brands by name

Popular brands

JVC KD-G701, Service Manual

Search results

Summary of Contents for KD-G701

Reviews:

Related manuals for KD-G701

Brands by name

Popular brands