EN
37
Automatic Sat-
ellite Program
Recording
SP/LP/EP
This facility allows you to automatically record a satellite
program which is timer-programmed on your external satellite
receiver. Connect a satellite receiver to the recorder's rear
AUDIO/VIDEO IN connectors and program the timer on the
satellite receiver; the recorder starts recording when the signals
input from the satellite receiver to the rear AUDIO/VIDEO IN
connectors, and when there is no input signals the recorder
stops recording and the power shuts off.
Before performing the following steps:
• Program the timer on the satellite receiver.
• Insert a cassette with the safety tab in place.
SET TAPE SPEED
1
Press
SP/LP/EP
to set the tape speed.
ENGAGE AUTO SATELLITE
PROG REC MODE
2
Press and hold
REC LINK
for about 2 seconds. The REC
LINK indicator lights up and the recorder turns off
automatically.
●
To disengage the Auto Satellite Prog Rec mode, press
REC LINK
. The REC LINK indicator goes off.
●
If the recorder's power is off, it is not possible to
engage the Auto Satellite Prog Rec mode.
ATTENTION
●
Be sure not to turn on the satellite receiver before the
program is executed; otherwise, the recorder will start
recording when the satellite receiver's power is turned
on.
●
If you have connected another appliance other than a
satellite receiver to the rear AUDIO/VIDEO IN
connectors, be sure not to engage the Auto Satellite Prog
Rec mode; otherwise, the recorder will start recording
when the connected appliance's power is turned on.
●
Auto Satellite Prog recording and timer-recording cannot
be done at the same time.
NOTES:
●
Auto Satellite Prog recording is only possible with the rear AUDIO/VIDEO IN connectors.
●
When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is
finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON”.
●
For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.
●
Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.
●
The REC LINK indicator blinks while Auto Satellite Prog recording is in progress.
●
Pressing the recorder's
button while Auto Satellite Prog recording is in progress turns off and recorder's power and disengages
the Auto Satellite Prog Rec mode.
●
If there is more than one satellite program you wish to record with Auto Satellite Prog Recording, it is not possible to set a different
tape speed for each; the tape speed selected in step
1
will apply to all the programs for Auto Satellite Prog recording.
●
The B.E.S.T. (
pg. 24) does not work while Auto Satellite Prog recording is in progress.
●
Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the program or may
record slightly longer than the actual length of the program.
●
If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite
Prog recording even though the button's light blinks. When the satellite receiver shuts off once and is turned back on again, the
recorder starts recording.
●
You can also record a program from your cable system in the same way if the system has a timer and is connected to the recorder's
rear AUDIO/VIDEO IN connectors.
●
When you press the recorder's
REC LINK
button to engage the Auto Satellite Prog Rec mode, if the REC LINK indicator does not
light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work
properly with that satellite receiver*.
If this is the case, perform “Express Timer Programming” (
pg. 30) to timer-record a satellite program.
*
Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.
●
After Automatic Satellite Program Recording, the number of recorded programs will not be displayed on the front display panel for
the instant Review function (
pg. 18).
REC LINK
REC LINK
indicator
HR-S5900/5990AM-EN26-46
5/9/02, 4:31 PM
37
Summary of Contents for HR-S5900AM
Page 66: ...MEMO ...
Page 67: ...MEMO ...
