13
J* Protocol Interface Hardware
Description
The serial command interface uses Pins 2
and 3 on the Control connector. The
voltage levels are TTL levels.
Caution:
Do not use RS-232C voltage levels.
The interface is not designed to support
the use of negative voltage levels.
Voltage inputs to Pin 2 and 3 should not
be below 0 V or exceed 5 V.
Genlock Signal Input
Caution:
When using an AC Adaptor, please
comply with Limited Power Source
(LPS) standards.
To reduce the emission of unwanted radio
waves, be sure to attach the provided clamp
filter as shown in the figure below.
Attach the clamp filter as close to this device
as possible, as shown below.
Power Supply
Turning On/Off the Power
After connecting to power cable, the unit
with power ON, causing the Power LED
light to turn red.
After disconnecting the power cable, the unit
will power OFF and the Power LED will turn
off.
The camera requires a voltage input of DC 12
– 15 V with a current drawn of >2.5 A. The
cable used to power the unit should be
terminated with Hirose part number
HR10A-7P-4S and the pinout is:
The full serial command set is described in
the section in Appendix A regarding the J*
Command Interface.
POWER
CONNECTOR
ON
BACK
OF
UNIT
HIROSE HR10A-7P-4S
TO AL-CM46B-01A CONTROL CONNECTOR
PIN DESCRIPTION
1
Voltage Input
2
Voltage Input
3
Ground
4
Ground
The genlock input is a standard tri-level sync
input. It is input on Pin 6 of the Control
connector.
The Genlock status of Power LED (red) is
as follows:
ON:
Normal operation that does not Genlock
OFF*:
Lock waiting status
*
after inputted Genlock source
Blinks slowly:
Locked status as normal
operation
Blinks quickly:
Genlock Error
If an error occurs, please check the
Genlock source and reboot the unit by
turning OFF/ON the power.
Do not operate the ProCam UHD until lock
is completed after Genlock source is
inputted.
Caution:
Synchronizing Signal to Use
HD Synchronizing Signal:
HDT
V
Tri-level synchronizing signal
Supports SMPTE274M-HD
1080i
SD Synchronizing Signal:
Black Burst signal
Supports SMPTE170M (RS-170A)-NTSC
Supports ITU-R BT.470-6 PAL
17
J* Protocol Interface Hardware
Description
The serial command interface uses Pins 2
and 3 on the Control connector. The
voltage levels are TTL levels.
Caution:
Do not use RS-232C voltage levels.
The interface is not designed to support
the use of negative voltage levels.
Voltage inputs to Pin 2 and 3 should not
be below 0 V or exceed 5 V.
Genlock Signal Input
Caution:
When using an AC Adaptor, please
comply with Limited Power Source
(LPS) standards.
To reduce the emission of unwanted radio
waves, be sure to attach the provided clamp
filter as shown in the figure below.
Attach the clamp filter as close to this device
as possible, as shown below.
Power Supply
Turning On/Off the Power
After connecting to power cable, the unit
with power ON, causing the Power LED
light to turn red.
After disconnecting the power cable, the unit
will power OFF and the Power LED will turn
off.
The camera requires a voltage input of DC 12
– 15 V with a current drawn of >2.5 A. The
cable used to power the unit should be
terminated with Hirose part number
HR10A-7P-4S and the pinout is:
The full serial command set is described in
the section in Appendix A regarding the J*
Command Interface.
POWER
CONNECTOR
ON
BACK
OF
UNIT
HIROSE HR10A-7P-4S
TO AL-CM46B-01A CONTROL CONNECTOR
PIN DESCRIPTION
1
Voltage Input
2
Voltage Input
3
Ground
4
Ground
The genlock input is a standard tri-level sync
input. It is input on Pin 6 of the Control
connector.
The Genlock status of Power LED (red) is
as follows:
ON:
Normal operation that does not Genlock
OFF*:
Lock waiting status
*
after inputted Genlock source
Blinks slowly:
Locked status as normal
operation
Blinks quickly:
Genlock Error
If an error occurs, please check the
Genlock source and reboot the unit by
turning OFF/ON the power.
Do not operate the ProCam UHD until lock
is completed after Genlock source is
inputted.
Caution:
Synchronizing Signal to Use
HD Synchronizing Signal:
HDT
V
Tri-level synchronizing signal
Supports SMPTE274M-HD
1080i
SD Synchronizing Signal:
Black Burst signal
Supports SMPTE170M (RS-170A)-NTSC
Supports ITU-R BT.470-6 PAL
17
GENLOCK IN terminal.
Caution:
●
Do not operate the 4K Camera Module
until lock is completed after Genlock
source is inputted.
●
The Genlock status of Power LED (red)
is as follows:
ON:
Normal operation that does not
Genlock
OFF*:
Lock waiting status
*after inputted Genlock source
Blinks slowly:
Locked status as
normal operation
Blinks quickly:
Genlock Error
●
If an error occurs, please check the
Genlock source and reboot the unit by
turning OFF/ON the power.