1-20 (No.86772)
•
Torque driver
Be sure to use to fastening the mechanism and exterior parts
because those parts must strictly be controlled for tightening
torque.
•
Bit
This bit is slightly longer than those set in conventional torque
drivers.
•
Tweezers
To be used for removing and installing parts and wires.
•
Chip IC replacement jig
To be used for adjustment of the camera system.
•
Cleaning cloth
Recommended the Cleaning cloth to wipe down the video
heads, mechanism (tape transport system), optical lens sur-
face.
•
Guide driver (Hexagonal)
To be used to turn the guide roller to adjustment of the linarity
of playback envelope.
•
INF adjustment lens
To be used for adjustment of the camera system. For the
usage of the INF adjustment lens, refer to the Service Bulletin
No. YA-SB-10035.
•
INF lens holder
To be used together with the Camera stand for operating the
Videocamera in the stripped-down condition such as the sta-
tus without the exterior parts or for using commodities that are
not yet conformable to the interchangeable ring. For the usage
of the INF lens holder, refer to the Service Bulletin No. YA-SB-
10035.
•
Camera stand
To be used together with the INF adjustment lens holder. For
the usage of the Camera stand, refer to the Service Bulletin
No. YA-SB-10035.
•
Light box assembly
To be used for adjustment of the camera system. For the
usage of the Light box assembly, refer to the Service Bulletin
No. YA-SB-10035.
•
Gray scale chart
To be used for adjustment of the camera system. For the
usage of the INF adjustment lens, refer to the Service Bulletin
No. YA-SB-10035.
•
Color bar chart
To be used for adjustment of the camera system. For the
usage of the INF adjustment lens, refer to the Service Bulletin
No. YA-SB-10035.
•
Alignment tape
To be used for check and adjustment of interchangeability of
the mechanism.
•
PC cable
To be used to connect the Videocamera and a personal computer
with each other when a personal computer issued for adjustment.
•
Communication cable
Connect the Communication cable between the PC cable and
Jig connector cable when performing a PC adjustment.
•
Service support system
To be used for adjustment with a personal computer. Software
can be downloaded also from JS-net.
•
Jig connector cable
Connected to CN110 of the main board and used for electrical
adjustment, etc.
4.2
JIG CONNECTOR CABLE CONNECTION
Connection procedure
Jig connector diagrams
TO JLIP_RX
TO JLIP_TX
TO GND
TO ENV_OUT
TO HID1
MENU
RS232C
COM PORT
SERVICE SUPPORT SYSTEM
PC CABLE
FOR
COMMUNICATION CABLE
COMMUNICATION CABLE
COMMUNICATION CABLE
JIG CONNECTOR
OSCILLOSCOPE
JIG CONNECTOR
PERSONAL COMPUTER
COVER
(JIG)
JIG CONNECTOR CABLE
JIG CONNECTOR
(CN110)
ADJUST
SCREW
SCREW
WHITE
RED
BLACK
GUIDE ROLLER (SUP)
GUIDE ROLLER (TU)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
JIG BOARD ASSEMBLY(14PIN)
JIG CONNECTORCABLE(YTU93082C)
VPPD
JLIP_TX
GND
HID1
PB CLK
ENV_OUT
MAIN VCO
ATFI
FS_PLL
Flashwrt
IF_TX
CJIG_RST
SRV_TX
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
JIG BOARD ASSEMBLY(15PIN)
TDI
TDO
TMS
TCK
TRST
SPA
SBE
GND
DISCRI
DRST
AL_3VSYS
SRV_RX
RX_DSC
TX_DSC
JLIP_RX
