JVC DT-V1900CG Instructions Manual Download Page 17

Page: 17 / 31

HOW TO USE “SETUP MENU”

(cont'd)

COLOR SYSTEM :AUTO
SYNC SELECT :AUTO
RUSH DELAY TIME :STD.
TALLY SELECT :GREEN
REMOTE SYSTEM :MAKE
EMBEDDED :1G
HOUR METER X100h :000

EXIT:

ADJUST:- + SELECT:

䡵

ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS

1. FUNCTION SETTING

Selects the colour system and
displays the monitor’s power-up
time or the total usage time.
Press the

button to display

the setting menu illustrated on
the right.

Item

: COLOR SYSTEM

Settings

: AUTO/NTSC/PAL

Function

: Selects the colour system when using the video

input card.
AUTO : Change NTSC and PAL automatically.
NTSC : Keeps the colour system NTSC.
PAL

: Keeps the colour system PAL.

NOTE : Normally select AUTO. However, if the input signal is

unstable, select NTSC or PAL.

Item

: SYNC SELECT

Settings

: AUTO/INT.

Function

: Select the detection method for synchronised

signals.
AUTO : If a synchronised signal is input from

external synchronised signal terminals,
the input video signal is synchronised
with it. If no synchronised signal is input,
the input video signal is synchronised
with its own built-in sync signal.

INT.

: The input video signal is always

synchronised with the built-in sync signal.

* The external synchronised signal terminals apply to the HD/

CS terminal and VD terminal (in the RGB/COMPONENT
Input Card), or the EXT. SYNC terminal (in the VIDEO Input
Card).

Item

: RUSH DELAY TIME

Settings

: STD./SLOW

Function

: Sets the time when the power supply to the

monitor’s circuits (excluding the micro computers)
starts after the power switch is pressed.
STD.

: The power supply starts approx.

1 second after the power switch is
pressed.

SLOW : The power supply starts approx.

3.2 seconds after the power switch is
pressed.

NOTE : When turning on many Multi-Format Monitors

simultaneously, it is recommended to use SLOW to
control rush current.

Item

: TALLY SELECT

Settings

: GREEN/RED

Function

: Selects the colour of the tally lamp (when lit) on

the upper front panel.
GREEN: The tally lamp lights in green.
RED

: The tally lamp lights in red.

NOTE : Set the MAKE/TRIGGER terminal’s tally control in the

REMOTE (external control) terminal setup menu. For
details, refer to Page 20. To set the color, use TALLY
SELECT in the "FUNCTION SETTING" setup menu or
MAKE/TRIGGER in the REMOTE (external control)
terminal setup menu. For details, refer to Page 16 and 20.

Item

: REMOTE SYSTEM

Settings

: MAKE/TRIGGER

Function

: Selects the contact system (MAKE (make

contact) or TRG. (trigger contact)) for the MAKE/
TRIGGER terminals.
MAKE (make contact system): Controls the

function by stable disconnection (terminal
open) or short-circuit (short with GND of 15th
terminal) of the controlled terminal.

TRG. (trigger system): Controls the function by

instantaneously (one second) short-circuiting
(short with GND of 15th terminal) the
controlled terminal.

Item

: EMBEDDED

Settings

: 1G/2G/1-2G

Function

: Selects AES/EBU Embedded Audio signal

channels.

NOTE: The auto setting mixes and outputs all 8 signal

channels. Output level is automatically detected and
set at FPGA according to the channel numbers that
are receiving signals.

* About sound output level
Sound output level is set to a standard output level for all
channels when several sound channels are output at the
same time. The more channels are selected, the lower each
channel’s level will be.
(Each channel's level becomes half for 1– 2 channel, 1/4 for
1– 4 channel.)
*About AUTO
When AUTO is selected, the number of sound channels in use
is detected. The level of each channel is automatically
adjusted to ensure that the total sound output level is equiva-
lent to the standard output level.

Item

: HOUR METER X100h

Number
range

: 000 ~ 655

Function

: Displays the total usage time of the monitor in

hundred-hour units.

CONTRAST : 00
BRIGHT : 00
CHROMA : 00
PHASE : 00
NTSC SETUP : 00
COMPO.LEVEL :SMPTE
sub menu
reset

EXIT:

ADJUST:- + SELECT:

●

When the timer passes 655, it returns to 000.