JVC DR-MX1S Instructions Manual Download

Page: 75 / 100

Masterpage:Right+

Filename [MX1S_11Editing.fm]

EDITING

Page 75

Saturday, 30 October 2004 16:18

You can use a camcorder as the source player and your unit as the
recording deck.

Make connections.

If the camcorder has no S-VIDEO output connector:

— connect the camcorder’s AUDIO/VIDEO OUT connectors to the
unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on the front
panel.

●

When using a monaural camcorder, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.

If the camcorder has an S-VIDEO output connector:

— connect the camcorder’s AUDIO OUT and S-VIDEO OUT
connectors to the unit’s [AUDIO] and [S-VIDEO] input connectors
on the front panel.

Press

VHS/HDD/DVD SELECT

on the unit repeatedly to select

the recording deck.

Press

CH +/–

to select “F-1”.

●

Set “FRONT AUX F-1” to “VIDEO” for the VIDEO input connector, or
“S-VIDEO” for the S-VIDEO input connector, depending on the
connector being used. (

墌

pg. 83)

Press

REC MODE

repeatedly to set the recording mode.

Start playback on the camcorder slightly before the actual point

from where you wish to start dubbing.

Press

on the unit to start recording. Or while holding

, press

on the remote control. The dubbing starts.

Press

on the unit, then stop playback on the camcorder.

NOTES:

●

All necessary cables can be obtained from your dealer.

●

Refer to the camcorder’s instruction manual for operating procedure.

●

The quality of dubbed picture becomes poorer than that of the
original.

Edit From A Camcorder

If the camcorder has no S-VIDEO output connector:

Recorder

Player

To [VIDEO/AUDIO
((MONO) L/R)] input

Audio/video cable
(not supplied)

AUDIO/VIDEO OUT

If the camcorder has an S-VIDEO output connector (HDD

& DVD deck only):

[S-VIDEO]

input

To [AUDIO] input

S-video cable
(not supplied)

AUDIO OUT

Audio cable
(not supplied)

S-VIDEO OUT

Recorder

Player

●

Slide the

TV/CABLE/DBS/DVD

switch to

DVD

MX1S_00.book Page 75 Saturday, October 30, 2004 4:18 PM

Summary of Contents for DR-MX1S





































































































Search results

Summary of Contents for DR-MX1S

Reviews:

Related manuals for DR-MX1S

Brands by name

Popular brands

JVC DR-MX1S, Instructions Manual

Search results

Summary of Contents for DR-MX1S

Reviews:

Related manuals for DR-MX1S

Brands by name

Popular brands