Masterpage:Right-No-Heading
EN
79
Filename [DR-M10SE_10Editing.fm]
Page 79
February 12, 2004 5:23 pm
A
Make connections.
Connect a camcorder or DV equipment to the DV IN
connector on the unit’s front panel.
B
Prepare the unit for dubbing.
C
Press
w e
to move
H
to
, then press
ENTER
.
D
Press
rt
repeatedly to select the desired sound track,
then press
ENTER
.
●
Note that this selection is not available when the source
programme is recorded in 16BIT (48 kHz) mode.
E
Press
REC MODE
repeatedly until the desired
recording speed appears. (
C
Prepare the DV equipment for dubbing.
Locate the point from where you want to start dubbing,
then stop or pause playback by pressing the following
buttons on the remote control:
4
,
5
,
3
,
8
,
9
●
To play back in slow speed (1/10 of the normal speed), press
9
to pause playback, then press
3
or
5
.
●
To play back frame-by-frame, press
9
to pause playback, then
press
9
repeatedly. Each press of
9
advances a frame.
●
To change the playback direction, press
3
or
5
.
D
Start dubbing.
Press
w e
to move the arrow to
, then press
ENTER
.
●
Playback on the external DV equipment and recording on the
unit should start simultaneously.
●
When the playback from the beginning is not possible, the
“DV DUBBING” controller cannot be used. Perform dubbing
without using the “DV DUBBING” controller. (
墌
right
column)
●
To pause dubbing, press
w e
to move
H
to
, then
press
ENTER
. Both the unit and the external DV equipment
pause dubbing. Pressing
9
on the unit also works the same
way.
●
To clear the “DV DUBBING” controller from the TV screen,
press
ON SCREEN
.
E
Stop dubbing.
Press
8
on the remote control.
●
Both the unit and the external DV equipment stop dubbing.
NOTES:
●
Dubbing copyright guarded programmes is not possible.
●
Original DV informations such as the recording date and time
are not recorded.
●
The superimposed indication during the operation or dubbing
is not recorded.
●
Only DV format image can be dubbed; MPEG2 format image
cannot be dubbed.
Performing dubbing without using the “DV DUBBING”
controller
A
Press
PR +/–
to set the channel to “DV DUBBING”.
B
Press
REC MODE
repeatedly until the desired recording
speed appears.
C
Start playback on the external DV equipment slightly before
the actual point from where you wish to start dubbing.
D
Press and hold
7
, then press
4
on the remote control, or
press
7
on the unit.
●
Dubbing starts.
E
When the dubbing ends, press
8
on the unit, then stop
playback on the external DV equipment.
A
Load a DVD-RAM/RW/R
disc on the unit.
B
Press
PR +/–
to set the
channel to “DV
DUBBING”.
●
The “DV DUBBING”
controller appears on the TV
screen.
●
If “
” does not appear on
the “DV DUBBING”
controller, make sure the DV
equipment is connected
correctly.
AUDIO 1
:
Select this to record the original stereo sound
played back on the connected DV
equipment.
AUDIO 2
:
Select this to record the dubbed stereo sound
played back on the connected DV
equipment.
MIX
:
Select this to record the sound of both
“AUDIO 1” and “AUDIO 2”.
DR-M10SE_01.book Page 79 Thursday, February 12, 2004 9:08 PM
