JVC DR-DX5SEK, Instructions Manual

Page: 36 / 92

Filename [DX5SEK_06DVD Operation.fm]
Masterpage:Left+
36
EN
BASIC OPERATIONS ON DVD DECK
Page 36Thursday, 10 November 2005 16:34
Free Rate Function
To record the entire programme, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the programme to be recorded and either the
remaining disc space or the specified recording time (from 60
minutes to 480 minutes).
8
To record the entire programme within the actual remaining
disc space (DVD deck only)
Select A FR (JUST) B in a recording mode selection procedure.
●
Note that this function is available only for timer programming
recording (
A
pg. 46, 48) and dubbing from HDD to DVD
(
A
pg. 58).
8
To record the entire programme by specifying the desired
recording time
Select A FR60–FR360 B , A FR420 B or A FR480 B in a recording mode
selection procedure. (
A
pg. 34, 37, 46, 48)
8
To record a 25-min. long daily programme five times just on
the same DVD disc for example
Perform A VIDEO Plus+ Timer Programming B (
A
pg. 46)
procedure. Be sure to set the recording mode to A FR125 B and set
Weekly/Daily Rec Function to A MON-FRI B in step 8 to fit the total
recording time to the whole disc space.
When the same programme is recorded in SP mode instead of in
A
FR125
B
, the 5th programme cannot be recorded.
NOTES:
●
You can programme this unit to timer record, regardless of the
disc remaining time. When the disc remaining time is not enough,
the unit performs
A Relief Recording B (
A
pg. 48). To avoid this,
make sure of the disc remaining time before setting timer
programming.
(Example) If you programmed to timer record for 60 minutes in
SP mode on a 120-minute disc, the disc remaining time would be
30 minutes in XP mode, 60 minutes in SP mode, 120 minutes in
LP mode, 180 minutes in EP mode, and 240 minutes in FR480
mode. Timer recording will not complete beyond these remaining
times.
●
The maximum recording time of FR (JUST) mode is the same as
the recording time of FR480 mode. When timer programming a
long programme in FR (JUST) mode on a disc whose remaining
time is short, it is recommended to check the disc remaining time
in FR480 mode to see if the remaining time is enough for the
programme.
●
Even if more than one programme are timer programmed in FR
(JUST) mode, only the first one is recorded.
●
In order to ensure that the recording fits on the disc, this feature
may leave a slight non-recorded section at the end of the disc.
●
There may be some noise and sound disturbance at the point on
the disc where the unit switches the mode.
Receiving Stereo And Bilingual Programmes
Your unit is equipped with a Digital stereo sound decoder (NICAM)
making reception of stereo and bilingual broadcasts possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
NOTES:
●
A SUPERIMPOSE B must be set to A AUTO B . Otherwise the on-
screen displays will not appear. (
A
pg. 73)
●
If the quality of stereo sound being received is poor, the
broadcast might be received in monaural with better quality.
Selection Of The Audio Channel To Be Recorded On A
Disc
When a programme is recorded on a DVD-RAM or DVD-RW disc in
VR mode, all audio channels of the receiving programme are
recorded on the disc. When you record a programme on a DVD-R
or DVD-RW disc in video mode, select the desired audio channel
(
A NICAM B or A MONO B ) to be recorded on the disc. (
A
pg. 72)
NOTE:
Before playing back a programme recorded in stereo, or a bilingual
programme, refer to
A Audio Channel Selection B (
A
pg. 28).
Blank
A: 1st
B: 2nd
C: 3rd
D: 4th
E: 5th
A: 1st
B: 2nd
C: 3rd
D: 4th
E: Blank (20 min.)
Blank
Type of Broadcast Being
Received
On-Screen Display
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
DX5SEK_00.book Page 36 Thursday, November 10, 2005 4:35 PM