background image

G-1

  CAUTION:         TO REDUCE THE RISK OF ELECTRIC SHOCK.
                         DO NOT REMOVE COVER (OR BACK)
                      NO USER SERVICEABLE PARTS INSIDE.
  REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, 
within an equilateral triangle is intended to 
alert the user to the presence of uninsulated 
“dangerous voltage” within the product's 
enclosure that may be of sufficient 
magnitude to constitute a risk of electric 
shock to persons.

The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance.

CAUTION

WARNING: TO REDUCE THE RISK OF FIRE 
OR ELECTRIC SHOCK, DO NOT EXPOSE 
THIS APPLIANCE TO RAIN OR MOISTURE.

For U.S.A.

This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the 
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that 
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION—

 STANDBY/ON button!

Disconnect the mains plug to shut the power off completely (all
lamps and indications go off). The 

 STANDBY/ON button in

any position does not disconnect the mains line.
• When the unit is on standby, the STANDBY lamp lights red.
• When the unit is turned on, the STANDBY lamp goes off.

The power can be remote controlled.

ATTENTION—Touche 

 STANDBY/ON

Déconnectez la fiche secteur pour mettre l’appareil
complètement hors tension (tous les témoins et toutes les

indications s’éteignent). La touche 

 

STANDBY/ON dans

n’importe quelle position ne déconnecte pas l’appareil du
secteur.
• Quand l’appareil est en mode de veille, le témoin STANDBY

est allumé en rouge.

• Quand l’appareil est sous tension, le témoin STANDBY s’

éteint.

L’alimentation ne peut pas être commandée à distance.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:
1.

Do not remove screws, covers or cabinet.

2.

Do not expose this appliance to rain or moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1.

Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.

2.

Ne pas exposer l’appareil à la pluie ni à l’humidité.

IMPORTANT FOR LASER PRODUCTS

1.

CLASS 1 LASER PRODUCT

2.

CAUTION

: Do not open the top cover. There are no user

serviceable parts inside the unit; leave all servicing to
qualified service personnel.

3.

CAUTION

: Visible and invisible laser radiation when open

and interlock failed or defeated. Avoid direct exposure to
beam.

4.

REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED INSIDE THE UNIT.

IMPORTANT POUR PRODUITS LASER

1.

PRODUIT LASER CLASSE 1

2.

ATTENTION

: N’ouvrez pas le couvercle supérieur. Il n’y a

aucune pièce réparable par l’utilisateur à l’intérieur de
l’appareil; confiez toute réparation à un personnel qualifié.

3.

ATTENTION

: Risque de radiations laser visible et invisible

quand l’appareil est ouvert et que le système de
verrouillage ne fonctionne pas ou a été mis hors service.
Évitez toute exposition directe au rayon.

4.

REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE
PRÉCAUTION PLACÉE À L’INTERIEUR DE
L’APPAREIL.

Warnings, Cautions and Others

 Mises en garde, précautions et indications diverses

FS-G2[C]safety.p65

04.11.5, 7:38 AM

1

Summary of Contents for CA-FSG2

























































Reviews: