Juniper SRX240 Series Hardware Manual Download Page 71

Page: 71 / 198

CHAPTER 11

Installing the Services Gateway

•

Preparing the SRX240 Services Gateway for Installation on page 53

•

Installing the SRX240 Services Gateway on page 53

Preparing the SRX240 Services Gateway for Installation

You can mount an SRX240 Services Gateway in a rack. The services gateway can be
mounted on four-post (telco) racks, enclosed cabinets, and open-frame racks.

Table 31: SRX240 Services Gateway Preinstallation Checklist

Additional Information

Task

“General Site Guidelines for Installing the SRX240
Services Gateway” on page 30

Verify that the installation site meets the
requirements.

“Unpacking the SRX240 Services Gateway” on
page 51

Remove the services gateway chassis from
the shipping carton.

“Verifying Parts Received with the SRX240 Services
Gateway” on page 51

Verify the parts you have received.

Documentation

General Site Guidelines for Installing the SRX240 Services Gateway on page 30

•

Unpacking the SRX240 Services Gateway on page 51

•

Verifying Parts Received with the SRX240 Services Gateway on page 51

•

Installing the SRX240 Services Gateway on page 53

Installing the SRX240 Services Gateway

You can front-mount or center-mount the SRX240 Services Gateway in a rack.

NOTE:

If you are installing multiple devices in one rack, install the lowest one

first and proceed upward in the rack.

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands