manualshive.com logo in svg

JS Automation Corp CPU-2616 PCI-104, User Manual

Share
Download
JS Automation Corp CPU-2616 PCI-104 User Manual Download Page 30

 

29

Flat Panel Type 

See the Flat Panel Display Table   

Available Options:

 Auto and TFT   

Default setting:

 Auto   

 

Flat Panel Display LCD Type Table

Resolution 

320x240 
640x480 
800x600 

1024x768 
1152x864 

1280x1024 
1600x1200 

 

Data Bus Type 

This field specifies the Data Bus width and data type   

Available Options:

 18,24 bits, 1 ppc and 18,24 bits, 2 ppc   

Default setting:

 18,24 bits, 1 ppc     

 

Refresh Rate 

This field specifies the refresh rate required by the panel   

Available Options:

 60 Hz, 70Hz, 72 Hz, 75 Hz, 85 Hz, 90 Hz and 100 Hz   

Default setting:

 60 Hz     

 

HSYNC/VSYNC Polarity Active 

This field specifies the HSYNC/VSYNC signal to the panel   

Available Options:

 Low and High   

Default setting:

 Low   

 

LP Active Period 

This field specifies the LDE/MOD signal to the panel   

Available Options:

 Free running and Active Only   

Default setting:

 Free running 

 

Summary of Contents for CPU-2616 PCI-104























































Reviews:

No comments

Brands by name

Popular brands

Load more brands