The following activation and set-up procedure should be used for all JR XP8103 and XP8103DT (Digital Trim) systems.
Note: Some early XP8103 systems will require the activation of the CCPM software through the Horizon Service Center. It’s easy to identify if
your system has the CCPM function activated by identifying if the “SWASH TYP” function appears in the System Mode as shown in
Section A below. Please refer to Section A to access the System Mode.
Prior to activating the CCPM function, it is first suggested that the Data Reset Function be performed to reset the desired model number
to be used back to the factory default settings.
Caution: Prior to performing the Data Reset function, it will be necessary to select the desired model number to be used.
A) Press the UP and DOWN keys simultaneously while turning the
power switch on to enter the System Mode. Next, press the UP or
DOWN keys to move the cursor to the Model Select Function. Press
the UP and DOWN keys simultaneously to enter the Model Select
Function. Select the desired model number to be used, then press
the CLEAR key to reset the current model to the factory default
settings. Press the UP and DOWN keys simultaneously to exit the
Model Select Function.
B) P ress the U P or D O W N keys to move the cursor to the S
WA S H
T
Y P E
Function, then press the U P and D O W N keys simultaneously to access the
Swashplate Type Fu n c t i o n.
Note: If the Swashplate Type Function is not present, it can be
activated by the Horizon Service Center. Please call for details.
Press the UP or DOWN keys until 3 servo 120° appears on the
screen. Press the UP and DOWN keys simultaneously two
times to exit the Swashplate Type Function and the System
Mode.
C) Turn the power switch on, then press the UP and DOWN keys simultaneously to enter the Function
Mode. Press the UP key until Swash Mix appears on the screen. Once this has been completed, it
will be necessary to change the value of the Pitch Function from the factory default setting of 60, to
a value of -50 using the + and - keys.
D) Press the UP key until R
EV
. S
W
. (Servo Reversing) appears on the screen. Next, reverse Channels 1,
2, and 4 by moving the cursor with the CH key, then pressing the + or - keys.
E) Press the UP key until TRVL. ADJ. (Travel Adjust) appears on the screen. Adjust the values as
shown using the channel key to move the cursor, and the + and - keys to set the value. Press the
S
EL
K
EY
to access the pitch channel values and set as indicated. Please note that the required travel
values will vary based on the type of servo selected. Please also note that the throttle travel values may vary based on the type of engine
used. This value can be fine tuned once the throttle linkage has been installed.
Note: The travel values shown for the rudder function are for use with Piezo type gyros, like the JR NEJ-900, NEJ-400, NEJ-450, and
NEJ-3000 type gyros. If a conventional mechanical type gyro is used (JR 120, 130, etc), then the travel values of the rudder
channel will need to be reduced to approximately 100%.
CCPM SOFTWARE ACTIVATION AND INITIAL ADJUSTMENT, CONTINUED
3 8
2. JR XP8103/XP8103DT SYSTEMS
[SYSTEM M.]
• INFO-DISP
• Model SEL
• MDL Name
• Type SEL
• MDL Reset
• MODULAT
• TRANSFER
• INPUT SEL
• SWASH TYP
[MDL Reset]
MODEL 1
HELI SPCM
PIT.
£H 100%
L 100%
AUX3
+ 100%
- 100%
[TRVL ADJ.]
£THRO
H 110%
L 110%
AILE
£L 100%
R 100%
ELEV
D 100%
U 100%
RUDD
£
L 150%
R 150%
[SWASH TYP]
1servo
NORM
[SWASH MIX]
3servos
120•
[SWASH TYP]
3servos
120•
3servos 120°
AILE
60%
ELEV
60%
∞ PIT.
-50%
Adjust Pitch Valve to -50%
Throttle travel values may vary depending
upon engine used
[REV.SW]
1
2
3
4
5
6
7
8
ch
R E V .
NO R M .
PIT.
£H 120%
L 120%
AUX3
+ 100%
- 100%
[TRVL ADJ.]
£THRO
H 130%
L 130%
AILE
£L 120%
R 120%
ELEV
D 120%
U 120%
RUDD
£
L 150%
R 150%
Digital Servos/Super Servos
Standard Servos
Throttle travel values may vary depending
upon engine used
