manualshive.com logo in svg

Jorjin WG1300-B0, User Manual

Share
Download
Jorjin WG1300-B0 User Manual Download Page 5

                                       

Doc No: WG1300BE00 EM Board-UG-R02 

 

                                                                                                                                                                           

Copyright 

©

 JORJIN TECHNOLOGIES INC. 2014 

http://WWW.JORJIN.COM.TW 

CONFIDENTIAL

 

Page 4 

Industry Canada statement: 
 

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to 

the following two conditions: (1) This device may not cause harmful interference, and (2) 

this device must accept any interference received, including interference that may cause 

undesired operation. 

 

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux 

appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions 

suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce 

dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de 

provoquer un fonctionnement indésirable. 

 

Radiation Exposure Statement: 

This equipment complies with IC radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with minimum distance 

20cm between the radiator & your body. 

 

Déclaration d'exposition aux radiations: 

Cet équipement est conforme aux limites 

d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet 

équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la 

source de rayonnement et votre corps. 

 

This device is intended only for OEM integrators under the following conditions: (For 

module device use) 

1) The antenna must be installed such that 20 cm is maintained between the antenna and 

users, and 

2) The transmitter module may not be co-located with any other transmitter or antenna. 

As long as 2 conditions above are met, further transmitter test will not be required. 

However, the OEM integrator is still responsible for testing their end-product for any 

additional compliance requirements required with this module installed. 

3) The monopole chip antenna with 2.5 dBi gain was verified in the conformity testing. 

Radiated transmit power must be equal to or lower than that specified in the Equipment 

Authorization. A separate approval is required for all other antenna type, or higher gain 

antenna. 

 

Summary of Contents for WG1300-B0

























Reviews:

No comments

Brands by name

Popular brands

Load more brands