Jonsered GR 2026CL Operator'S Manual Download Page 23 | Manualshive

Page: 23 / 32

background image

English

– 23

TECHNICAL DATA

Technical data

Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various
working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.

NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting
equipment fitted. The table indicates the highest and lowest values.

Technical data

GR 2026L/CL

GR 2032L

Engine

Cylinder displacement, cu.in/cm

3

1,64/26,9

1,88/30,8

Cylinder bore, inch/mm

1,38/35

1,38/35

Stroke, inch/mm

1,10/28

1,26/32

Idle speed, rpm

2700

2700

Recommended max. speed, rpm

11000-11700

11000-11700

Speed of output shaft, rpm

10000

10000

Max. engine output, acc. to ISO 8893, kW/ rpm

0,9/9000

1,1/8400

Catalytic converter muffler

Yes

Yes

Speed-regulated ignition system

Yes

Yes

Ignition system

Manufacturer/type of ignition system

Walbro CD

Walbro CD

Spark plug

NGK BPMR 7A/
Champion RCJ 7Y

NGK BPMR 7A/
Champion RCJ 7Y

Electrode gap, inch/mm

0,02/0,5

0,02/0,5

Fuel and lubrication system

Manufacturer/type of carburetor

Walbro WT

Walbro WT

Fuel tank capacity, US pint/litre

1,06/0,5

1,06/0,5

Weight

Weight without fuel, cutting attachment and guard, Lbs/kg

L: 12,6/5,7 CL: 13,2/6,0 13,7/6,2

Sound levels

(see note 1)

Equivalent noise pressure level at the operator’s ear,
measured according to EN/ISO 11806 and ISO 7917, dB(A),
min./max.:

95/99

92/100

Vibration levels

Vibration levels at handles, measured according to
ANSI B175.3-1997, m/s

2

At idle, left/right handles, min.:

2,8/2,0

2,5/2,3

At idle, left/right handles, max.:

2,8/2,0

4,0/3,0

At max. speed, left/right handles, min.:

2,6/2,8

3,8/2,7

At max. speed, left/right handles, max.:

5,0/5,0

6,8/3,4

Approved accessories

Type

Cutting attachment guard, Art. no.

Centre hole in blades/cutters, Ø 25,4 mm

Arbor shaft thread M10

Plastic blades

Polytrim Ø 300

503 74 50-03

Trimmer head

Tap-N-Go 35

503 74 50-03

Auto32

503 74 50-03

S35

503 74 50-03

Edger (CL)

Edger attachment Ø 200 mm

-

Hedge trimmer (CL)

Hedge trimmer attachment

-

«
...
21
22
23
24
25
...
»

Summary of Contents for GR 2026CL

































Reviews:

No comments

Related manuals for GR 2026CL

Brand: Echo Pages: 40

Brand: Daewoo Pages: 18

Brand: Gardena Pages: 15

Brand: Sovereign Pages: 16

Brand: Fieldmann Pages: 108

Brand: Status Pages: 40

Brand: p5 Pages: 28

Brand: Jonsered Pages: 20

Brand: Jonsered Pages: 36

Brand: Powerplus Pages: 16

Brand: Raider Pages: 80

Brand: Hoftronic Pages: 7

Brand: Flymo Pages: 80

CONTOUR POWER PLUS CORDLESS CCT25

Brand: Flymo Pages: 72

Brand: EarthQuake Pages: 28

Brand: Shindaiwa Pages: 28

Brand: Makita Pages: 104

Brand: Ferm Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands