manualshive.com logo in svg

Johnson Pump MCHC, Instruction Manual

Share
Download
Johnson Pump MCHC Instruction Manual Download Page 34

MCHZ/EN (0912) 4.2

Disassembly and assembly

33

MCHZ

7.4.6

Assembling the bearing construction

See figure 10.

1 Fit the bearing cover (0100) to the inside of the bearing housing for the drive side, 

this is the part which has the arrow for the direction of rotation.

2 Fit an internal circlip (0230) into the inner groove in the bearing housing.

3 Fix this bearing housing (0010) to the pressure bracket with the bolts (0290).

4 Fit the rubber V-ring (0240) over the pump shaft, with the narrow opening pointing to 

the inside of the pump.

5 Fit the external circlip (0220) into the rear of the 2 grooves on the pump shaft and fit 

the filling ring (0100).

6 Grease the bearing on both sides with ball bearing grease (

not for 2RS-1 type 

bearings!

). For the correct type of grease see paragraph 10.6 "Post-greasing of ball 

bearings".

7 Fit the bearing (0210) over the pump shaft and into the seat of the bearing housing 

using a suitable assembly bush which rests on both the inner and outer rings of the 
bearing.

8 Fit the other filling ring (0100) and external circlip (0220) to the pump shaft.

9 Fit the internal circlip (0230) into the bearing housing.

10 Fit the outermost bearing cover (0110) and the rubber V-ring (0240), with the narrow 

opening pointing to the outside of the pump.

Figure 10:

Bearing construction.

4755

Summary of Contents for MCHC























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands