manualshive.com logo in svg

Johnson Electric AB51, User Manual, Page: 42 / 50

Share
Download
Johnson Electric AB51 User Manual Download Page 42

AB5 and AB51 Drivers User Manual  

 

Technical Data 

 

Nanomotion Ltd.  

 

41

 

  Control Terminal Block Pinout  

5.4.3

Pin 

Signal Name 

Function 

Description 

1 

+24V 

Input  

+24 Vdc power supply 

2 

GND  

Ground 

 

3 

+Vin 

Input 

Analog command from 
controller. 

4 

-Vin 

Input 

Analog command from 
controller.  

5 

Enable 

Input 

Enable. See section  5.5.1  

Table 

6

: Control Terminal Block Pinout 

  Motor Output Port Pinout 

5.4.4

Pin 

Signal Name 

Function 

Description 

1 

GND 

Power supply 
ground 

Safety input; shorted to pin 6 
in order to verify the motor 
connection and to prevent 
driver operation without the 
motor. 

2 

N.C. 

Not used 

 

3 

Motor_Up 

High voltage output 

Connected to the white motor 
terminal.  

4 

Motor_Common 

High voltage output 

Connected to the black motor 
terminal. 

5 

Motor_Down 

High voltage output 

Connected to the red motor 
terminal. 

6 

Motor_Connected 

Input 

Safety input; shorted to pin 1 
in order to verify the motor 
connection and prevent the 
driver operation without the 
motor. 

7 

GND 

Power supply 
ground 

Shorted to the shield 

8 

N.C. 

Not used 

 

9 

N.C. 

Not used 

 

Table 

7

: Motor Output Port Pinout 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for AB51



















































Reviews:

No comments