TFP2242
Page 4 of 4
NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
TEFLON is a registered trademark of DuPont
1400 Pennbrook Parkway, Lansdale, PA 19446 | Tel1-215-362-0700
© 2018 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
Step 8.
Connect system pipe or fitting.
• Threaded Fitting Installations
(Figure 1) - With TEFLON paste
sealant applied to IFP Fitting pipe
threads, connect system fitting. A
leak-tight 3/4 inch NPT fitting joint
should be obtained by applying
minimum-to-maximum torque of
10 to 20 lb-ft (13,4 to 26,8 N·m).
Higher levels of torque can distort
the Fitting inlet with consequent
leakage of Fitting or impairment of
Nozzle.
• Socket-Weld Fitting Installations
(Figure 2) - Insert prepared end of
3/4 Inch system pipe into IFP Fitting
weld socket until fully engaged.
Weld full circumference of pipe at
juncture with face of IFP Fitting
weld socket.
Care and
Maintenance
The TYCO Type IFP AQUAMIST
Recessed Nozzle Fittings must be
maintained and serviced in accordance
with this section.
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system
that it controls, obtain permission to
shut down the affected fire protection
system from the proper authorities
and notify all personnel who may be
affected by this action.
Type IFP AQUAMIST Recessed Nozzle
Fittings must never be painted, plated,
coated or altered in any way after
leaving the factory; otherwise, the
spray performance may be impaired.
Care must be exercised to avoid
damage to the nozzles -before, during,
and after installation. Nozzles damaged
by dropping, striking, wrench twist/slip-
page, or the like, must be replaced.
Frequent visual inspections are rec-
ommended to be initially performed
for nozzles installed in potentially cor-
rosive atmospheres to verify the integ-
rity of the materials of construction and
finish as they may be affected by the
corrosive conditions present for a given
installation. Thereafter, annual inspec-
tions per NFPA 25 are required.
The owner is responsible for the inspec-
tion, testing, and maintenance of their
fire protection system and devices in
compliance with this document, as well
as with the applicable standards of the
NATIONAL FIRE PROTECTION ASSO-
CIATION (e.g., NFPA 25), in addition to
the standards of any other authorities
having jurisdiction. Contact the install-
ing contractor or nozzle manufacturer
with any questions.
Water spray fixed systems should be
inspected, tested, and maintained by
a qualified Inspection Service in accor-
dance with local requirements and/or
national codes
If the Cap does not remain in place on
the Fitting, it is recommended that the
Link/Cap Subassembly be replaced.
Limited
Warranty
For warranty terms and conditions, visit
www.tyco-fire.com.
Ordering
Procedure
Contact your local distributor for avail-
ability. When placing an order, indicate
the full product name and Part Number
(P/N).
Type AM31 Nozzle with NPT
Threaded IFP Fitting and
Cap Assembly
Specify: Type AM31 AQUAMIST Nozzle
with NPT Threaded IFP Fitting and Cap
Assembly, Stainless Steel, P/N 28227
Type AM31 Nozzle with Socket-
Weld IFP Fitting and Cap Assembly
Specify: Type AM31 AQUAMIST Nozzle
with Socket-Weld IFP Fitting and Cap
Assembly, Stainless Steel, P/N 28228
Type AM31 Nozzle with NPT
Threaded IFP Fitting and Dust Cap
Assembly
Specify: Type AM31 AQUAMIST Nozzle
with NPT Threaded IFP Fitting and Flu-
orosilicone Dust Cap, Stainless Steel,
P/N 28251
Type AM31 Nozzle with Socket-
Weld IFP Fitting and Dust Cap
Assembly
Specify: Type AM31 AQUAMIST Nozzle
with Socket-Weld IFP Fitting and Flu-
orosilicone Dust Cap, Stainless Steel,
P/N 28252
Type AM10 Nozzle with NPT
Threaded IFP Fitting and
Cap Assembly
Specify: Type AM10 AQUAMIST Nozzle
with NPT Threaded IFP Fitting and Cap
Assembly, Stainless Steel, P/N 28242
Type AM10 Nozzle with Socket-
Weld IFP Fitting and Cap Assembly
Specify: Type AM10 AQUAMIST Nozzle
with Socket-Weld IFP Fitting and Cap
Assembly, Stainless Steel, P/N 28243
Sprinkler Wrench
Specify: W-Type 29 Sprinkler Wrench,
P/N 28241
REPLACEMENT PARTS
Link/Cap Subassembly
Specify: Link/Cap Subassembly, Stain-
less Steel, P/N 000028230
Type AM31 AQUAMIST Nozzles
Specify: Type AM31 AQUAMIST
Nozzle, Stainless Steel finish, P/N
28229
Type AM10 AQUAMIST Nozzles
Specify: Type AM10 AQUAMIST Nozzle,
Stainless Steel, P/N 49-207-0-001
Dust Cap Assembly
Specify: Model F885 Dust Cap Assem-
bly, Fluorosilicone, with Stainless Steel
Wire, P/N 28247*
*Refer to Technical Data Sheet TFP2299 for installation
instructions.
