Johnson Controls TRUE RH HC-67x3 Installation Instructions Manual Download Page 7

 

T

RUE

RH Series HC-67x3 Humidity Controllers Installation Instructions    

7

 

Technical Specifications 

Product 

T

RUE

RH Series HC-67x3 Humidity Controllers 

Power Requirements 

14 to 30 VDC at 10 mA or 20 to 30 VAC, 50/60 Hz at 15 mA with no load, Class 2 

Control Action 

Jumper selectable, direct or reverse (factory set for reverse acting) 

Output Range 

Jumper selectable, 0 to 10 VDC (factory set) or 6 to 9 VDC; 5 k ohm minimum load 
impedance 

Humidity 

Element:  

All-Polymer™ element 

Sensing Range: 

0 to 100% RH, non-condensing 

Setpoint:  

Adjustable from 20 to 80% RH 

Proportional Band: 

Adjustable from 2 to 20% RH 

Temperature Coefficient 

-0.1 to 0.05% RH/°C at 5°C (41°F) to -0.07 to -0.21% RH/°C at 65°C (149°F) 

Electrical Connections 

3-position screw terminal block 

Ambient Operating 

Conditions 

32 to 122°F (0 to 50°C) 
0 to 100% RH, non-condensing; 85°F (29°C) maximum dew point 

Survival Operating 

Conditions 

-22 to 140

°

F (-30 to 60

°

C) 

0 to 100% RH, non-condensing; 85°F (29°C) maximum dew point 

Ambient Storage 

Conditions 

-40 to 176°F (-40 to 80°C) 
0 to 100% RH, non-condensing; 85°F (29°C) maximum dew point 

Materials 

Wall Mount: 

White plastic enclosure for surface or wallbox mounting, including  

 

hardware 

Duct Probe: 

Light gray plastic cover with dark gray plastic housing and probe 

Dimensions 

Wall Mount (H x W x D): 

3.20 x 3.20 x 1.34 in. (81 x 81 x 34 mm) 

Duct Probe (H x W x D): 

3.25 in. x 3.25 in. x 8.27 in. (83 mm x 83 mm x 210 mm) 

Probe (L x D): 

6.25 in. x 0.98 in. (159 mm x 25 mm) 

Shipping Weight 

0.7 lb (0.3 kg) 

Agency Compliance 

Duct Probe Material: 

94-5 V flammability rated per UL 94 

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these 
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or 
misuse of its products. 

Building Efficiency

 

507 E. Michigan Street, Milwaukee, WI  53202 

 

 

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.  

All other marks herein are the marks of their respective owners. © 2014 Johnson Controls, Inc.

 

 

Summary of Contents for TRUE RH HC-67x3








Reviews: