manualshive.com logo in svg

Johnson Controls Metasys NCE25 series, Installation Instructions Manual, Page: 35 / 38

Share
Download
Johnson Controls Metasys NCE25 series Installation Instructions Manual Download Page 35

Table 18: NCE25 Ordering Information (Releases 9.0 and 9.0.7 Only)

Product Code

Number

Release Description

MS-NCE2561-0

9.0

Supports two third-party trunks (Modbus RTU or TCP, M-Bus, or

KNX) and one MS/TP Bus. The number of supported devices on

the third-party trunk depends on the protocol. For the MS/TP

bus, up to 32 devices are supported. Includes internal modem.

MS-NCE2566-0

9.0.7

Supports two third-party trunks (Modbus RTU or TCP, M-Bus, or

KNX) and one MS/TP Bus. The number of supported devices on

the third-party trunk depends on the protocol. For the MS/TP

bus, up to 32 devices are supported. Includes integral display

screen.

MS-NCE2567-0

9.0

Supports two third-party trunks (Modbus RTU or TCP, M-Bus, or

KNX) and one MS/TP Bus. The number of supported devices on

the third-party trunk depends on the protocol. For the MS/TP

bus, up to 32 devices are supported. Includes integral display

screen and internal modem.

Technical specifications

Table 19: NCE25

Power Requirement

Dedicated nominal 24 VAC, Class 2 power supply (North America),

SELV power supply (Europe), at 50/60 Hz (20 VAC minimum to 30 VAC

maximum)

Power Consumption

25 VA maximum for NCE25 only

Note: 

The 25 VA rating does 

not

 include any power supplied

by the NCE to devices connected at the NCE BOs. BO devices

connected to and powered by an NCE can require an additional

125 VA (maximum).

Power Source

+15 VDC power source terminals provide 100 mA total current; quantity

of inputs: five, located in Universal IN terminals; for active (3-wire) input

devices

Ambient Operating

Conditions

0°C to 50°C (32°F to 122°F), 10 to 90% RH, 30°C (86°F) maximum dew

point

Ambient Storage

Conditions

-40°C to 70°C (-40°F to 158°F), 5% to 95% RH, 30°C (86°F) maximum dew

point

Data Protection Battery

Supports data protection on power failure. Rechargeable NiMH battery:

3.6 VDC 500 mAh, with a typical life of five to seven years at 21°C (70°F);

Product Code Number: MS-BAT1020-0

Processors

Supervisory Controller:

 192 MHz Renesas SH4 7760 RISC processor

Field Controller:

 20 MHz Renesas H8S2398 processor

Memory

Supervisory Controller: 

128 MB flash nonvolatile memory for

operating system, configuration data, and operations data storage and

backup and 128 MB SDRAM for operations data dynamic memory

Field Controller: 

1 MB flash memory and 1 MB RAM

35

NCE25 Installation Instructions

Summary of Contents for Metasys NCE25 series







































Reviews:

No comments