manualshive.com logo in svg

Johnson Controls Metasys NCE25 series, Installation Instructions Manual, Page: 31 / 38

Share
Download
Johnson Controls Metasys NCE25 series Installation Instructions Manual Download Page 31

network activity.)

2.  The BATT FAULT, PEER COM, and FAULT LEDs shut Off. The RUN LED flashes to indicate that the

NCE software is loading.

3.  The LEDs display the operational status of the network engine. When the RUN LED goes On

Steady, startup is complete and the network engine is operational.

The total time to start up the network engine depends on the size of the database and can take

several minutes.
Table 15: LED designations, normal status, and descriptions

LED designation

Normal status

Descriptions/other conditions

POWER (Green)

On steady

On Steady = Unit is getting power from either the

battery or 24 VAC power.
Off Steady = Unit is shut down.

FAULT (Red)

Off steady

Off Steady = Normal operation.
On Steady = General Fault. CCT application may

be corrupted or missing. Some FAULT conditions

are user-configurable in the 

Metasys

 software. Pre-

configured fault conditions include excessive CPU

flash or memory use, excessive board temperature.
Blink - 2 Hz = Download or Startup in progress, not

ready for normal operation.
Blink Rapidly - 5 Hz = One or more defined SA

Bus devices are offline. Check SA Bus devices for

problems, including low batteries on wireless

sensor.

SA BUS (Green)

Blinking

Blinking - 5 Hz = Data Transmission (normal

communication)
Off Steady = No Data Transmission
On Steady = Communication lost, waiting to join

communication ring

FC BUS (Green)

Flicker

Flicker = Normal communications; the FC Bus

is transmitting and receiving data. Flickers are

generally synchronized with data transmission but

do not use them to indicate specific transmission

times. Off Steady = No field controllers are defined

to FC Bus in the network engine. This LED is always

OFF on LON models with 9.0.7 software.

MODEM RX

Flicker

Not functional on 9.0.7 engines.

MODEM TX

Flicker

Not functional on 9.0.7 engines.

BATT FAULT (Red)

Off steady

On Steady = Battery defective. Flicker = Data

Protection Battery is not installed. Connect or install

battery.

31

NCE25 Installation Instructions

Summary of Contents for Metasys NCE25 series







































Reviews:

No comments