background image

FEU16x0 Field Equipment Controller Installation Instructions

13

Repair Information

If you need to replace the MS-FEU1611-0U controller, contact the Johnson Controls Repair Center in Louisville, 
Kentucky, at 1-502-671-7312. This model has special restrictions because it is UL 864 10th Edition UUKL/ORD-
C100-13 UUKLC listed for smoke control.

Accessories

Use 

Table 5

 to order accessories.  

Technical Specifications  

Table 5:  FEU16 Accessories Ordering Information

Product Code Number

Description

PAN-PWRSP-U

Transformer, 120/24 VAC, 96 VA, with circuit breaker and 120 VAC outlet, approved for Smoke 
Control

MS-FUSE01-1

Replacement fuse (Bulk Pack of 10)

FEU1610 Controller

Product Code Numbers

MS-FEU1610-0U Field Equipment Controller

Supply Voltage

20 - 30 VAC at 50 or 60 Hz, Class 2

Power Consumption

10 VA typical, 14 VA maximum, plus all BO and CO loads

Ambient  Conditions

Operating:

 0 to 50°C (32 to 122°F); 10 to 90% RH noncondensing

Storage:

 -40 to 70°C (-40 to 158°F); 10 to 90% RH noncondensing

Terminations

Screw Terminals and Screw Terminal Pluggable Blocks

Controller Addressing

DIP switch set (4-127). Addresses 0-3, 128-255 are reserved.

Communications Bus

BACnet® MS/TP; 3-wire FC Bus between the NAE and other devices. 4-wire SA Bus 
between network sensors and other devices.

Mounting

On flat surface with screws on three mounting clips or a single 35 mm DIN rail

Housing

Plastic housing
Plastic material: ABS and polycarbonate UL94 5VB

Analog Input/Analog 
Output Resolution and 
Accuracy

Analog Input Points: 15-bit resolution
Analog Output Points: 16-bit resolution, +200 mV accuracy

Dimensions 
(Height x Width x Depth)

144 x 127 x 58 mm (5.68 x 5 x  2.25 in.)
Minimum space for mounting:

 

174 x 350 x 110 mm (6.8 x 13.8 x 4.3 in.)

Weight

0.5 kg  (1.10 lb)

Compliance

United States:

 UL Listed, File E107041, CCN PAZX, UL 916, Energy Management 

Equipment; FCC Compliant to CFR47, Part 15, Subpart B, Class A
UL Listed, File S4977, UL 864 UUKL/UUKLC 10th Edition Listed, Smoke Control Units and 
Accessories for Fire Alarm Systems Equipment

Canada:

 UL Listed, File E107041, CCN PAZX7, CAN/CSA C22.2 No. 205, Signal 

Equipment; Industry Canada Compliant, ICES-003
UL Listed, File S4977, UL 864 UUKL/ORD-C100-13 10th Edition Listed, Smoke Control Units 
and Accessories for Fire Alarm Systems 

Europe:

 CE Mark, EMC Directive, in accordance with EN 61000-6-3 and EN 61000-6-2, and 

the Low Voltage Directive in accordance with EN 60730.

Australia and New Zealand: 

RCM Mark, Australia/NZ Emissions Compliant.

BACnet International: 

BACnet Testing Laboratories™ (BTL) 135-2004 Listed BACnet 

Application Specific Controller (B-ASC)

The performance specifications are nominal and conform to acceptable industry standard. For application at conditions beyond these 
specifications, consult the local Johnson Controls office. Johnson Controls shall not be liable for damages resulting from misapplication or 
misuse of its products.

Summary of Contents for Metasys MS-FEU1610-0U















Reviews: