manualshive.com logo in svg

Johnson Controls LN Series, Installation Instructions Manual

Share
Download
Johnson Controls LN Series Installation Instructions Manual Download Page 16

LN Application Specific, Remote I/O, and Free Programmable Controllers Installation Instructions

16

Technical Specifications   

   

             

Table 4:  LN Application Specific Controllers

Product Codes

LN-RTUL-1, LN-FCUL-1, LN-UVL-1, LN-HPUL-1

Power Requirement

Voltage:

 24 VAC, +15%, 50/60HZ, Class 2

Protection:

 1.35 A auto reset fuse

Power Consumption: 

6 VA

Maximum Consumption: 

15 VA

Environmental

Operating Temperature: 

0 to 70ºC, (32 to 158ºF)

Storage Temperature:

 -20 to 70ºC, (-4

 

to 158ºF)

Relative Humidity: 

0 to 90% noncondensing

General

Standard:

LN-RTUL-1: Roof Top Unit Controller #8030
LN-FCUL-1: Fan Coil Controller #8020 
LN-UVL-1: Unit Ventilator #8080
LN-HPU-1: Heat Pump with Temperature Control #8051

Processor:

 Neuron™ 3150®; 8 bits

Processor Speed: 

10 MHz

Memory: 

Nonvolatile Flash 64k (APB application and configuration properties)

Communication:

 LonTalk® protocol

Media Channel: 

TP/FT-10; 78 Kbps

Transceiver:

 FT-X1

Status Indicator: 

Green LED – power status and LON TX, Orange LED – service

and LON RX

Communication Jack: 

LON audio jack mono 1/8 in (3.5 mm)

Enclosure

Material:

 ABS type PA-765A

Dimensions (with screws):

 5.7 x 4.7 x 2.0 in. (144.8 x 119.4 x 50.8 mm)

Shipping Weight:

 0.77 lbs. (0.35 kg)

Inputs

Quantity: 6

Input Types:

 universal software configurable

Voltage: 0 to 10 VDC , Ac0.5%
Current: 4 to 20 mA with a 249 ohm external resistor (wired in parallel), Accuracy 
+0.5%
Digital: dry contact

Resistor:

RTD: 1k ohm (nickel and platinum), 100 ohm (platinum)
Thermistor: Type 2 and Type 3 10k ohm, accuracy: +0.9°F, +5°C
range: -40° to 257°F; resolution: 0.1°C; 0.18°F. 

Potentiometer:

 translation table configurable on several points; ac0.5%

Input Resolution:

 12-bit analog/digital converter

Outputs

Quantity: 

7

5 Digital:

 

Triac 1.0 A at 24 VAC
External power supply

2 Universal: 0 to 10 VDC (linear), digital 0 to 12 VDC (on/off) or PWM

PWM output: adjustable period from 2 second to 15 minutes

60 mA max. at 12 VDC (140

°F; 

60

°C)

Maximum load 200 ohms

Auto-reset fuse: 60 mA at 140

°F; 

60

°C; 100 mA at 68°F, 20°C

Output Resolution:

 8-bit digital/analog converter

Summary of Contents for LN Series


























Reviews:

No comments

Brands by name

Popular brands

Load more brands