Johnson Controls HIDH018B21S, Engineering Manual

Page: 484 / 668

CONTROL SYSTEM
6-168
TC-15001-rev.3
[ Switch Setting Procedure ]
6HWPRGL¿FDWLRQRIVZLWFKEHIRUHWXUQLQJ21&&&$
7KHVZLWFKVHWWLQJLVGHVFULEHGLQWKH7DEOH6RPHRIWKHVZLWFKHVPD\UHTXLUHPRGL¿FDWLRQDVRQVLWH
GHPDQGH[WHUQDORXWSXWZLWKZHWFRQWDFWVHWWLQJHWFDULVHV
Switch 8VDJH
Factory
Setting
Remarks
SW2
(8 poles DSW)
“OPTION”
1
21 1RUPDO2SHUDWLRQ0RGH
2))6HOI&KHFNLQJ0RGH:LWKDOOWKHRWKHU3LQV2))
ON
5HIHUWR>6HOI
&KHFNLQJ0RGH@IRUPRUH
details.
2 2)))L[HG OFF Do not change it.
3 2)))L[HG OFF Do not change it.
4 2)))L[HG OFF Do not change it.
2)))L[HG OFF Do not change it.
6 2)))L[HG OFF Do not change it.
7 2)))L[HG OFF Do not change it.
8 ON: IP Address Initialization OFF
Refer to 6.10.6.2.3
[Initialization of IP Address
Setting].
SW6
(8 poles DSW)
³02'(´
1 21)L[HG ON Do not change it.
2 2)))L[HG OFF Do not change it.
3 2)))L[HG OFF Do not change it.
4 2)))L[HG OFF Do not change it.
2)))L[HG OFF Do not change it.
6 2)))L[HG OFF Do not change it.
7 2)))L[HG OFF Do not change it.
8 2)))L[HG OFF Do not change it.
SW7
(2 poles DSW)
³+/,1.´
1
ON: 7HUPLQDWLQJUHVLV/,1.FLUFXLW$FWLYH
OFF: 7HUPLQDWLQJUHVLV/,1.FLUFXLW,QDFWLYH
OFF
:KHQDFWLYDWLQJWHUPLQDO
resistance on this adapter,
ensure no other terminating
UHVLVWDQFHH[LVWVRQWKH
VDPH+/,1.
2
ON: 3URWHFWLRQ)/,1.WUDQVPLVVLRQLVDYDLODEOH
6KRUW&LUFXLW
OFF: 3URWHFWLRQ)/,1.WUDQVPLVVLRQLVXQDYDLODEOH
(Normal)
OFF
Refer to the notice
described below.
SW8
(2 poles DSW)
³56´
1 2)))L[HG OFF Do not change it.
2 2)))L[HG OFF Do not change it.
6:
(3 poles DSW)
³([WHUQDO2XWSXW´
1
ON: ([WHUQDORXWSXW:HW&RQWDFW9'&216HWWLQJ
OFF: ([WHUQDORXWSXW'U\&RQWDFW9'&2))6HWWLQJ
OFF
Set ON when applying wet
contact setting.
2
ON: ([WHUQDORXWSXW:HW&RQWDFW9'&216HWWLQJ
OFF: ([WHUQDORXWSXW'U\&RQWDFW9'&2))6HWWLQJ
OFF
Set ON when applying wet
contact setting.
3
ON: ([WHUQDORXWSXW:HW&RQWDFW9'&216HWWLQJ
OFF: ([WHUQDORXWSXW'U\&RQWDFW9'&2))6HWWLQJ
OFF
Set ON when applying wet
contact setting.
6:36:VZLWFK
“OPTION”
7KLVVZLWFKLVXVHGIRUVHOIFKHFNLQJPRGH
Table 6.4 Switch Setting
The procedure for setting each switch is as follows:
(a) Turn OFF the power switch of CCCA01, and remove the top cover after checking that the LED is turned
OFF.
(b) Modify the Switch setting.
(c) Reinstall the top cover and turn ON the power to CCCA01.
In the case that an H-LINK fuse blows, a connection among an H-LINK fuse will be possible by turning ON
the pin 2 of SW7.
NOTE