Johnson Controls FX-PCV1615 Installation Instructions Manual Download Page 29

Page: 29 / 30

Table 10: FX-PCV1615/1626/1628/1630 Controllers

Canada:

UL Listed, File E107041, CCN PAZX7, CAN/CSA C22.2 No. 205,

Signal Equipment.
Industry Canada Compliant, ICES-003

Europe:

CE Mark – Johnson Controls declares that this product is in

compliance with the essential requirements and other relevant

provisions of the EMC Directive.

Australia and New Zealand:

RCM Mark, Australia/NZ Emissions Compliant.

BACnet International

BACnet Testing Laboratories (BTL) Protocol Revision 7 Listed

BACnet Application Specific Controller (B-ASC)

The performance specifications are nominal and conform to acceptable industry standard. For

application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson

Controls shall not be liable for damages resulting from misapplication or misuse of its products.

Points of single contact

APAC

Europe

NA/SA

JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 32 CHANGJIJANG RD NEW DISTRICT
WUXI JIANGSU PROVINCE 214028
CHINA

JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY

JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA

FX-PCV1615/1626/1628/1630 Programmable VAV Box Controllers Installation Instructions

Summary of Contents for FX-PCV1615































Search results

Summary of Contents for FX-PCV1615

Reviews:

Related manuals for FX-PCV1615

Brands by name

Popular brands

Johnson Controls FX-PCV1615, Installation Instructions Manual

Search results

Summary of Contents for FX-PCV1615

Reviews:

Related manuals for FX-PCV1615

Brands by name

Popular brands