background image

FCP-PA-701-NF

www.johnsoncontrols.com

Building Technologies & Solutions 

Headquarters: Milwaukee, Wisconsin, USA

 

Branch Offices: Principal Cities World-wide

© Copyright 2021 Johnson Controls.

All specifications and other information shown were current as of document revision and are subject to change without notice.

This product is covered by a limited warranty, details of which can be found at 

www.johnsoncontrols.com/buildingswarranty.

Product warranty

Contact information

Contact your local branch office: 

www.johnsoncontrols.com/locations

Contact Johnson Controls: 

www.johnsoncontrols.com/contact-us

Technical specifications

Specification

Description

Model

FCP-PA-701-NF

Power requirements

20 VAC to 30 VAC, 60 Hz, max. 3 A (3 VA at 24 V nominal)

Output rating

Valve outputs

1 A maximum per each relay channel

(Max. relays ON combination: 1 relay), 20 VAC to 30 VAC

Analog inputs

Remote sensor

10K ohm at 77°F (25°C) NTC sensor

Pipe sensor

10K ohm at 77°F (25°C) NTC sensor

Binary input

Set back

NC/NO dry contact switch

Local temperature sensor type

NTC temperature sensor, accurate to ±1°F (±0.6°C) at 77°F (25°C)

Remote temperature sensor type

NTC temperature sensor, accurate to ±2°F (±1.2°C) at 70°F (21°C)

Wire size 

18 AWG (100 ft [30.5 m] maximum) to 24 AWG (36 ft [11 m] maximum)

Temperature adjustment range

Heat mode

45°F to 90°F (7°C to 32°C)

Cool mode

60°F to 95°F (15°C to 35°C)

Accuracy

Local temperature 

sensor

±1°F (+/-0.6°C)

Remote temperature 

sensor

±2°F (±1.2°C) at 70°F (21°C)

Remote pipe sensor

±5°F (±3.0°C)

Deadband

2°F to 5°F (1°C to 3°C)

Ambient conditions

Operating

14°F to 122°F (-10°C to 50°C); 5% RH to 90% RH, noncondensing

Storage

-4°F to 140°F (-20°C to 60°C); 5% RH to 90% RH, noncondensing

Disconnection means

Type 1B

Pollution degree

2

Rated impulse voltage

330 V

Automatic action

100,000 cycles

Ratings for supply and loading

20 VAC to 30 VAC

Dimensions H x W x D

3.27 in. x 3.94 in. x 0.98 in. (83 mm x 100 mm x 25 mm)

Shipping weight

Product with packing and accessories: 10.1 oz (285 g)
Thermostat only: 4.9 oz (138 g)
Trim plate: 1.2 oz (33 g)

Compliance 

CONFORMS TO UL STD. 60730-1 & 60730-2-9

CERTIFIED TO CSA STD. E60730-1 & E60730-2-9

 

Table 8: 

FCP technical specifications

5013346

Summary of Contents for FCP-PA-701-NF











Reviews: