background image

- 34 -

User Guide

JVC85BCT

Frost Protection

1.Add 1 gallons (4L) recreational vehicle (RV) anti-freezing agent to the solution tank without 
dilution.

FOR SAFETY: Wear goggles to avoid contact with eyes.

ATTENTION: Before operating the machine next time, rinse the solution tank thoroughly to remove the 
anti-freezing agent.

TROUBLESHOOTING

PUSH, TOW AND TRANSPORT THE MACHINE

Trouble

 

Cause

 

Solution

 

 

 

Machine 
inoperable

 

Switch off or switch damaged

 

Turn switch on or replace it

 

Brush motor button off or damaged

 

Turn switch on or replace it

 

Vacuum motor button off or damaged

 

Turn switch on or replace it

 

Motor switch handle failure

 

Replace the micro-switch

 

Battery exhausted or damaged

 

Charge or replace batteries

 

Overload protector activated

 

Solve short circuit fault and 

press overload protector

 

Charger 

failure

 

Plug disconnected with power

 

Check for plug connection

 

False connection of battery terminals

 

Connect terminals properly

 

Charger breakdown

 

Refers to charger fault code

 

 

 

Brush motor 

failure

 

Brush lifted above ground or its 

button damaged

 

Replace brush motor micro- 

switch

 

Motor switch damaged

 

Replace motor micro-switch

 

Overload protector activated

 

Solve short circuit fault and 

press overload protector

 

Brush motor connector loosens

 

Refix the connector

 

Brush motor damaged

 

Replace the motor

 

 

 

Machine 

won't move

 

Universal wheel damaged

 

Replace the universal wheel

 

Duty caster damaged

 

Replace duty caster

 

 

Brush adjustment nut loosens

 

 

Readjust brush adjustment nut

 

 

 

 

 

 

 

Summary of Contents for JVC85BCT









































Reviews: