background image

TYPE 5610V/5610VQ

SINGLE O-RING CARTRIDGE SEAL

Installation, Operation & Maintenance Instructions

PAGE

8

If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be consulted prior to
their selection and use. In the interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without
prior notice. It is dangerous to smoke while handling products made from PTFE. Old and new PTFE products must not be incinerated. ISO 9001 and
ISO14001 Certified, details available on request.

©2015 John Crane 

Revised 10/15    

www.johncrane.com

                                                                                                                               IOM-5610/5610VQ

North America

United States of America

Tel:   1-847-967-2400
Fax:  1-847-967-3915

Europe

United Kingdom

Tel:   44-1753-224000
Fax:  44-1753-224224

Latin America

Brazil

Tel:   55-11-3371-2500
Fax:  55-11-3371-2599

Middle East & Africa

United Arab Emirates

Tel:   971-481-27800
Fax:  971-488-62830

Asia Pacific

Singapore

Tel:   65-6518-1800
Fax:  65-6518-1803

Summary of Contents for 5610V









Reviews: