Joerns WeCare Bed User & Service Manual Download Page 16

16

Joerns® Bed Frames
WeCare™ Bed

© 2022 Joerns Healthcare • 6110435 RevC • 22-2083

Trapeze Adapter (Figure 34)

1. 

The trapeze adapter is designed to allow 

attachment of the trapeze system to the WeCare™ 

Bed. Prior to use, please read important warnings 

related to this option and follow all instructions 

below.

2. 

Install the trapeze adapter according to the 

supplied instructions. If needed, call Technical 

Support at 800-826-0270 for instructions.

3. 

Install the trapeze assembly onto the trapeze 

adapter according to the trapeze manufacturer’s 

instructions.

4. 

Operate the bed from its highest through lowest 

positions to ensure proper clearance and 

operation. Some trapeze systems may not be 

suitable for use with the WeCare Bed, due to its 

low operating height. 

5. 

Adjustment and use of a trapeze should be in 

accordance with instructions from a healthcare 

professional (doctor or therapist).

6. 

Do not exceed the maximum load condition listed 

on installation instructions.

Figure 35

Figure 34

Drainage Bag Holder (Figure 35)

Warning: Possible BioHazard.

 Prior to use, consult 

the drain bag manufacturer’s installation and use 

instructions. Failure to do so could result in a bag 

puncture, resulting in a potential biohazard.

Warning: Possible Injury Or Death.

 Many items that 

attach to the holder are gravity fed and must be below 

the bed user to function. Do not allow items attached 

to the holder to rest or be positioned on the floor where 

they might be stepped on and adversely affected or 

damaged. Exercise particular caution when the bed is 

moved to its lowest position as items attached to the 

holder at that height are especially at risk. Failure to do 

so could result in injury or death.

Warning: Possible Injury Or Death

. Make sure items 

hung on this holder have proper clearance and are not 

pinched or caught during bed adjustment. Failure to do 

so could result in injury or death.

1.  The drainage bag holder is designed as an 

attachment point for items such as urine collection 

bags. Make sure items attached to holder are 

safely secured. Prior to use, please read important 

warnings related to the drainage bag holder and 

follow all instructions below.

2.  Install the drainage bag holder and attach items 

to the holder according to supplied instructions. If 

needed, call Technical Support at 800-826-0270 

for instructions.

3.  It is important to operate all bed functions through 

their entire ranges to ensure that items attached 

to the holder have proper clearance and are not 

pinched or caught.

4. 

Attach the holder only to the point and position 

outlined in installation instructions. Operate all 

bed functions through their full ranges to ensure 

that items attached to the holder have proper 

clearance and are not pinched or caught.

5. 

Many items that attach to the holder are gravity fed 

and must be below bed user to function. Do not 

allow items suspended from the holder to rest on 

the floor, particularly when the bed is in its lowest 

position. Otherwise, a safety condition may occur 

or the function of attached items may be impacted.

Summary of Contents for WeCare Bed





















Reviews: