background image

 

Page 3 of 4 

361-4175 

Compensating Valve Kit 

TH407 

 

326-1977 

Load Chart Kit  

 
 

For GROUP B UNITS Only:    

 

Model 

Quantity 

Part Number 

Description 

TH336 & TH406 

361-4174 

Compensating Valve Kit   

TH337 & TH407 

361-4175 

Compensating Valve Kit   

 
 
 

ACTION REQUIRED: 

  GROUP A UNITS  

    Remove the existing load chart book located in the cab and replace with the revised 

load chart.   Destroy and discard the original load chart booklet.    

    The Compensating Valve Kit must be installed on all affected units in accordance 

with the enclosed Compensating Valve Kit Installation Procedure.   

 

  GROUP B UNITS 

   The Compensating Valve Kit must be installed on all affected units in accordance 

with the enclosed Compensating Valve Kit Installation Procedure.  

 
SERVICE CLAIM ALLOWANCES: 

To receive reimbursement, file a service claim through the normal CAT service claims process.  
When filing this claim through the CAT system, please use the following codes in the 
appropriate input fields: 

Input Field 

Before Failure 

Part Causing Failure  

C111C3 

Group Number  

5086 

Warranty Claim Description  

56 

SIMS Description Code 

 

 

 

 

 

#C111C3

Summary of Contents for TH336












Reviews: