background image

JL AUDIO 

CleanSweep

 CL441dsp

JL AUDIO 

CleanSweep

 CL441dsp

INSTALLATION APPLICATIONS

This product is designed for operation in 

vehicles with 12V, negative-ground electrical 
systems. Use of this product in vehicles with 
positive ground and/or voltages other than 12V 
may result in damage to the product and will void 
the warranty.

This product is 

not

 certified or approved  

for use in aircraft.

PLANNING YOUR INSTALLATION

It is important that you take the time to  

read this manual and that you plan out your  
installation carefully. 

Safety Considerations: 

Your CleanSweep™ needs to be installed in a 

dry environment and in a manner which does not 
interfere with your vehicle’s safety equipment (air 
bags, seat belt systems, ABS brake systems, etc.). 
You should also take the time to securely mount 
the CleanSweep™ processor using the supplied 
screws so that it does not come loose in the event 
of a collision or sudden acceleration / deceleration.

Stupid Mistakes to Avoid:

•  Check before drilling any holes in your vehicle to 

make sure that you will not be drilling through a 
gas tank, brake line, wiring harness or other vital 
vehicle system.

•  Do not run system wiring outside or underneath 

the vehicle. This is an extremely dangerous 
practice which can result in severe damage to 
your vehicle and person.

•  Protect all system wires from sharp metal  

edges and wear by carefully routing them,  
tying them down and using grommets and  
loom where appropriate.

•  Do not mount this product in the engine 

compartment, under the vehicle, on the  
roof or in any other area that will expose it  
to the elements. 

SERIAL NUMBER  

In the event that your CleanSweep™ CL441dsp 

requires service or is ever stolen, you will need to 
have a record of the product’s serial number. Please 
take the time to enter that number in the space 
provided below.  The serial number can be found on 
the bottom panel of the unit and on the packaging.

Serial Number: 

PROTECT YOUR HEARING! 

We value you as a long-term customer. For 

that reason, we urge you to practice restraint in 
the operation of this product so as not to damage 
your hearing and that of others in your vehicle. 
Studies have shown that continuous exposure to 
high sound pressure levels can lead to permanent 
(irreparable) hearing loss.  Automotive audio 
systems are capable of producing such high sound 
pressure levels. Please limit your continuous 
exposure to high volume levels.

While driving, operate your audio system in a 

manner that still allows you to hear necessary noises 
to operate your vehicle safely (horns, sirens, etc.).

Summary of Contents for ClenSweep CL441 dsp

















Reviews: