background image

Warnings and Safety Precautions 

1. 

Read and keep these instructions. 

2. 

Heed all warnings. 

3. 

Follow all instructions. 

4. 

Clean only with a soft dry cloth. 

5.  Do not install near any heat sources such as radiators, heat 

registers, stoves, or other apparatus (including amplifiers) that 
produce heat. 

6.  Do not defeat the safety purpose of the three-prong grounding-

type plug. If the provided plug does not fit into your outlet, con-
sult an electrician for replacement of the obsolete outlet.  

7.  Do not use this unit if the electrical power cord is frayed or bro-

ken. The power cord should be routed so that it is not likely to 
be walked on or pinched by items placed upon or against it. 

8.  To reduce the risk of fire or electric shock, do not expose this 

apparatus to rain or moisture. 

9. 

Refer all servicing to qualified service personnel. 

10.  The following warning symbol may be used elsewhere in this 

manual: 

 

The exclamation point within an equilateral triangle is 
intended to alert the user of the presence of important 
operating and maintenance (servicing) instructions in 
the user guide. 

Summary of Contents for innkeeper LTD Digital Hybrid





















Reviews: