JK Audio innkeeper LTD Digital Hybrid User Manual Download Page 18

18 

This equipment has been tested and found to comply with the limits 
for a Class A digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against 
harmful interference when the equipment is operated in a 
commercial environment.  This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful 
interference to radio communications.  Operation of this equipment 
in a residential area is likely to cause harmful interference in which 
case the user will be required to correct the interference at his own 
expense. 
 
Changes or modifications not expressly approved by JK Audio can 
void the user's authority to operate the equipment. 

FCC Registration 

Your new JK Audio product has been registered with the Federal 
Communications Commission (FCC).  This product complies with 
the standards in Part 68 of the FCC rules.   
 

1.

 

Connection and use with the nationwide telephone network 

 

The FCC requires that you connect this telephone equipment to 
the national telephone network through a USOC RJ-11C 
modular telephone jack. 

 
 

This equipment may not be used with Party Line Service or 
Coin Telephone Lines. 

 
 

This equipment is hearing aid compatible. 

 

2.

 

Information for the telephone company 

 

Upon request from your local telephone company, you are 
required to provide the following information: 

 
  a) 

 The "line" to which you will connect the telephone 

equipment (that is, your telephone number), and 

 

FCC Part 15 Compliance 

Summary of Contents for innkeeper LTD Digital Hybrid





















Reviews: