background image

19 

FCC Registration 

(continued) 

 

b)  The telephone equipment's FCC registration number.  This 

can be found on the bottom of your telephone equipment, 
and, 

 
 

c)   The ringer equivalence number (REN) for this equipment.   

 
 

The REN is used to determine the quantity of devices which will 
be connected to the telephone line.  Excessive RENs on the 
telephone line may result in the devices not ringing in response 
to an incoming call.  In most, but not all areas, the sum of the 
RENs should not exceed 5.0.  To be certain of the number of 
devices that may be connected to the line, as determined by the 
total RENs, contact the local telephone company. 

 

3. Repair 

Instructions

 

  If it is determined that your telephone equipment is 

malfunctioning, the FCC requires that it not be used and that it 
be unplugged from the modular outlet until the problem has 
been corrected.  Repairs to this telephone equipment can only 
be made by the manufacturer or its authorized agents

 

or by 

others who may be authorized by the FCC.

   

For repair 

procedures, follow the instructions outlined under the warranty 
section of the manual. 

 

4.  Rights of the telephone company 

 

If telephone equipment is causing harm to the network, the 
telephone company may temporarily discontinue your telephone 
service.  If possible, they'll notify you before they interrupt 
service.  If advanced notice isn't practical, you'll be notified as 
soon as possible. You'll be given the opportunity to correct the 
problem, and you'll be informed of your right to file a complaint 
with the FCC. 

 
 

Your telephone company may make changes in its facilities, 
equipment, operations or procedures that could affect the 
proper functioning of your JK Audio product.  If such changes 
are planned, you'll be notified by your telephone company. 

Summary of Contents for innkeeper LTD Digital Hybrid





















Reviews: