background image

 

 

- 1

 

-

 

 

1. General Information 

1.1 Overview 

 

Thanks for choosing

 

Jinko Solar PV modules. In order to ensure the PV modules to 

be installed correctly, please read the following operation instructions carefully before 
modules installed and used.   

 

Please  remember  that  the  products  would  generate  electricity  and  certain  safety 
measures need to be taken to avoid danger. 

 

1.2 Applicable Products 

 

This document is applicable to the series of solar module as listed below:   
 

With 6” mono c

-Si: 

JKMxxxM-72 (xxx=250-335, in steps of 5, 72 cells)   
JKMxxxM-72-J (xxx=250-335, in steps of 5, 72 cells) 
JKMxxxM-72(Plus) (xxx=250-335, in steps of 5, 72 cells) 
JKMxxxM-60 (xxx=210-280, in steps of 5, 60 cells)

   

JKMxxxM-60-J (xxx=210-280, in steps of 5, 60 cells) 
JKMxxxM-60-(Plus) (xxx=210-280, in steps of 5, 60 cells) 
JKMxxxM-48 (xxx=170-220, in steps of 5, 48 cells) 
JKMxxxM-48-J (xxx=170-220, in steps of 5, 48 cells) 
JKMxxxM-72B (xxx=250-335, in steps of 5, 72 cells)* 
JKMxxxM-60B (xxx=210-280, in steps of 5, 60 cells) 
JKMSxxxM-72 (xxx=250-335, in steps of 5, 72 cells)** 
JKMSxxxM-72-J (xxx=250-335, in steps of 5, 72 cells) 
JKMSxxxM-72(Plus) (xxx=250-335, in steps of 5, 72 cells)*** 
JKMSxxxM-60 (xxx=210-280, in steps of 5, 60 cells) 
JKMSxxxM-60-J (xxx=210-280, in steps of 5, 60 cells) 
JKMSxxxM-60(Plus) (xxx=210-280, in steps of 5, 60 cells) 
JKMSxxxM-48-J (xxx=170-220, in steps of 5, 48 cells) 
JKMSxxxM-48(Plus) (xxx=170-220, in steps of 5, 48 cells) 

With 6” poly c

-Si: 

Summary of Contents for JKM M-48 Series






























Reviews: