JinkoSolar JKM M-48 Series Installation Manual Download

Page: 24 / 29

- 22

3. Wiring and connection

a) Before this procedure, please read the operation instructions of the PV system

carefully. Make wiring by Multi-connecting cables between the PV modules in

series or parallel connection, which is determined by user‟s configuration

requirement for system power, current and voltage.

b) PV module connected in series should have similar current. Modules must not be

connected together to create a voltage higher than the permitted system

voltage(1000VDC), as reference the maximum number of modules in series (N)

can be easily calculated by dividing the Maximum System Voltage of the modules

by the respective Voc value of the module. Any more please always take into

consideration the variation of the voltage under different temperatures, the Voc of

the modules will be rise when the temperature drops.

For example: with JKM190M-72 modules (Max. System voltage is 1000V) the

maximum series modules configuration number should NEVER can exceed N= 22

(1000V/45.2V = 22.1)

c) PV module connect in parallel should have similar voltage. As reference the

maximum number of modules in parallel (M) can be easily calculated by dividing

the maximum rated current (indicated in the electrical specification below) by Isc

value of the module, and then plus 1. Any more please always take into

consideration the variation of the current under different temperatures, the Isc of

the modules will be rise when the temperature goes up.

For example: with JKM190M-72 modules (the maximum rated current is 10A) the

maximum parallel modules configuration number should never exceed M= 2

(10A/5.56A+1=2.8).

d) Open the connection box of the control system and connect the cabled from the PV

arrays to the connection box in accordance with the installation indication of the PV

control systems. The cross-sectional area and cable connector capacity must

satisfy the maximum short-circuit of PV system (For a single component, we

recommended the cross-sectional area of cables is 4mm

and the rated current of

connectors is more than 10A), otherwise cables and connectors will become

overheating for large current. Please pay attention: the temperature limit of cables

is 85

℃

and the temperature limit of connector is 105

℃

e) All module frames and mounting racks must be properly grounded in accordance

Summary of Contents for JKM M-48 Series






























Search results

Summary of Contents for JKM M-48 Series

Reviews:

Related manuals for JKM M-48 Series

Brands by name

Popular brands

JinkoSolar JKM M-48 Series, Installation Manual

Search results

Summary of Contents for JKM M-48 Series

Reviews:

Related manuals for JKM M-48 Series

Brands by name

Popular brands