background image

consumers themselves.

6. Damage caused by flood, fire, earthquake and other irresistible natural factors

Tip: For products not covered by the Three Guarantees, the dealer shall provide paid

maintenance services, and the consumer shall bear all costs for maintenance,

replacement of parts, transportation, etc.

Disclaimer

UNISKY shall not be responsible for the failure of software /application/equipment

of the third party manufacturer, and shall not be liable for any damage to the bike

trainer caused by software not developed or recommended by UNISKY.

The user must carefully read this instruction before using the product,

completely follow the installation steps, installation methods, and inspection

requirements of this instruction to install and inspect the product and use the

product in accordance with the warning requirements. If the product is used in

violation of the warning, resulting in temporary or permanent damage to the user's

body (whether direct or indirect), or property damage, UNISKY shall not be liable.

Spare Parts List

Parts No.

Name

Quan

tity

Graphical Representation

A

Bike Trainer Stand

1

Summary of Contents for DJS-003



















Reviews: