STT1-14-GB(V1)
www.jilong.com
6
7
STT1-14-GB(V1)
www.jilong.com
4
IMPORTANT WARNING
INFLATING AND DEFLATING THE BOAT
To enhance the enjoyment of your boat and protect the safety of passengers and
operator using the boat, always strictly observe the following safety warning:
This is not a life saving device. Use only under competent supervision. Never allow
diving into this product. Never leave in or near the water when not in use. Never tow
from any vehicle. Adult assembly and operation required.
Adults should inflate the chambers in numbered sequence and use the printed ruler
on the hull of boat to check while inflating. Excessive inflating the boat can cause
the chambers to burst or cause damage to the welded seams.
Not following the operator’s instructions, which may detail important inflation and
assembly sequences
，
can cause capsizing and drowning.
Taking the boating safety course and get hands-on training from your boat dealer or
local boating authorities. Review all safety requirements regularly. Never navigate
alone.
A Personal Flotation Device (PFD) is required for each passenger. It is especially
important that children and non-swimmers wear a personal flotation device at all
times. Children and non-swimmers need special instruction in the use of PFD.
- Use caution when stepping or climbing aboard the boat. Step into the center
of the boat for maximum stability. Distribute the weight of passenger, gear, tackle
box and accessories evenly so that the boat sits even front to back and side to
side. Uneven distribution of persons or loads in the boat can cause capsizing and
drowning.
Do not use your boat if you suspect a puncture or leak. It might be unsafe.
BEWARE OF OFFSHORE WINDS AND CURRENTS. These could be unsafe
conditions.
Follow these rules to avoid drowning, paralysis or other serious injuries.
WARNUNG: It is the responsibility of the boat operator to identify and obey all local
and state laws pertaining to boat safety and required safety equipment. Please
consult your local authorities to ensure compliance.
Do not allow unattended children in the boat. Always make sure that at least one
responsible adult is supervising all children and those who don’t know how to swim
at all times.
Always maintain the proper boat safety equipment in an easily accessible place in
your boat. Indicate clearly emergency phone numbers as well as safety advisories
and rules (such as “No jumping or Diving”)
The total number of persons and total weight shall not exceed the information
printed on the boat. Do not exceed the maximum recommended capacities.
Exceeding the data given on the capacity plate can cause capsizing and drowning.
Inflating
If the boat is inflated during cold weather or without direct sunlight on the tubes,
care must be taken not to over-inflate the tubes. As the air inside the tubes heats
up due to temperature rises or sunshine, the pressure will increase. The boat is
not fitted with a safety valve, so the pressure must be monitored at all times.
Select a clean area free of stones, gravel, sticks or other sharp objects.
Defold the boat completely in the manner that the boat lays flat on the floor
evenly.
- Use a hand or foot operated air pump to inflate the boat.
Deflating:
Remove the valve completey from the valve seat and also remove the plug from
the inlet of the valve.
Press the valve base together for deflation.
Please inflate the chambers in the numeric order. If the boat is inflated too much,
it might burst or the seams might tear. Fill each chamber until it is stiff. Measure
the printed ruler to 10cm with the equipped hard ruler to check the main chamber
for proper inflation.
Due to changes in temperature the valves might become inflexible. To get them
flexible again please soak the closed valves in warm water for some minutes.
The boat does not have a safety valve. The air pressure has to be observed all
the time.
!!!! Please do NOT use an air compressor !!!!
185 x 98 x 28cm; 218 x 110 x36cm
MAXIMUM PRESSURE 0.035 bar (0.508 PSI) !!!
252 x 125 x40cm; 305 x 136 x42cm; 340 x 142 x48cm
MAXIMUM PRESSURE 0.05 bar (0.725 PSI) !!!
Inflate the screw valve:
1) Fix the big ring of valve
cap on the base
2) Screw the middle part of
valve cap on the base and
then inflating
3) Screw the small cap of
valve tightened
