background image

38

PI-078

June 2021

Warranty

Limited Warranty. 

Each Waterblast Unit, Bareshaft Pump, and Fluid End 

manufactured by Jetstream is warranted against defects in material and 
workmanship for a period of 12 months or 1,000 hours, provided it is 
used in a normal and reasonable manner and in accordance with all op-
erating instructions. If sold to an end user, the applicable warranty period 
commences from the date of delivery to the end user. If used for rental 
purposes, the applicable warranty period commences from the date of 
delivery to the party holding the equipment available for rent. This limited 
warranty may be enforced by any subsequent transferee during the 
warranty period. This limited warranty is the sole and exclusive warranty 
given by Jetstream.

Exclusive Remedy.

 Should any warranted product fail during the warran-

ty period, Jetstream will cause to be repaired or replaced, as Jetstream 
may elect, any part or parts of such Waterblast Unit, Bareshaft Pump, or 
Fluid End that the examination discloses in Jetstream’s sole judgment 
to be defective in material or factory workmanship. Repairs or replace-
ments are to be made at Jetstream in Houston, Jetstream FS Solutions 
Rental Center, the customer’s location, or at other locations approved by 
Jetstream. Labor is furnished only when the unit or part is returned to the 
factory or when travel and expenses are paid by the purchaser. Freight, 
travel and expenses incurred in connection with repair or warranty are 
excluded from this warranty and shall be paid by the purchaser. The 
foregoing remedies shall be the sole and exclusive remedies of any party 
making a valid warranty claim.
The Jetstream Limited Warranty shall NOT apply to (and Jetstream shall 
NOT be responsible for):
1. Major components or trade accessories that have a separate warranty 
from their original manufacturer, such as, but not limited to: diesel en-
gines, electric motors, electronic soft starter and/or across the line starter 
panels, axles, PTO’s, clutch packs, high pressure gauges, high pressure 
hoses, flex lances, etc.
2. Normal adjustments and maintenance services.
3. Normal wear parts such as, but not limited to: oil, clutches, belts, 
filters, packing, cartridges, univalves, face seals, diffusers, gland nut 
bushings, plungers, nozzles, rupture disks, etc.

Summary of Contents for Rotomag X22









































Reviews: