background image

 

To  adjust  the  cutting  height  release  the  winged  nut  (A,  Fig 
18)  and  move  the  upper  blade  guide  and  guard  assembly 
(B).

 

 

Fig. 18 

 

Blade Drift Compensation:

 

Blade drift is a frequent problem on rip cuts and during 
resawing. 

Blade drift may occur when the fence is being used, the 
blade begins to wander off the cutting line (Fig. 19). 

 

Fig. 19 

Blade drift can be caused by a number of factors. 

- The saw blade follows the grain 

- The saw blade is dull. 

- Blade guides not adjusted correctly. 

- Blade tension unsufficient.  

- Blade-

teeth have asymmetric“set”  

 

Auxiliary fence for rip fence:

 

For your own safety always set the upper saw guide as 
close to the workpiece as possible. 

For narrow shallow cuts on the rip fence a self-made 
auxiliary fence (E, Fig. 20) made of cutable material ( e.g. 
wood, plastic, aluminium) must be used. 
Length same as rip fence. 

 

                                       Fig. 20 

Mitre gauge: 

Place the mitre gauge in the table T-slot. 

Directions for  “safe operation“ : 

 

                Performing high resaw cuts 

 

Summary of Contents for JWBS-10


















Reviews: