Read and understand the entire
instruction manual before attempting
assembly or operation.
Keep this operating instruction close
by the machine, protected from dirt
and humidity, and pass it over to the
new owner if you part with the tool.
No changes to the machine may be
made.
Daily inspect the function and
existence of the safety appliances
before you start the machine.
Do not attempt operation in this case,
protect the machine by unplugging
the mains cord.
Do not lock the moving guard in the
open position. Ensure that the
movable guards operate freely
without jamming.
Remove all loose clothing and
confine long hair.
Before operating the machine,
remove tie, rings, watches, other
jewellery, and roll up sleeves above
the elbows.
Wear safety shoes; never wear
leisure shoes or sandals.
Always wear the approved working
outfit
Do
not
wear gloves while operating
this machine.
For the safe handling of saw blades
wear work gloves.
Observe the chapter “save operation”
in this manual.
Control the stopping time of the
machine, it may not be longer than 10
seconds.
Do NOT stop the blade by forcing the
machine or by using sideways
pressure.
Insure that the workpiece does not
roll when cutting round pieces.
Use suitable table extensions and
supporting aids for difficult to handle
workpieces.
Never use just your hands for
sawing
Always hold and guide the
workpieces safely during machining.
Never cut pieces that are too small.
For safety reasons this machine
requires the use of two hands and
should not be operated standing on a
staircase or leather.
Make sure that the motor ventilation
holes are clean and open.
Install the machine so that there is
sufficient space for safe operation
and workpiece handling.
Keep work area well lighted.
The machine is designed to operate
in closed rooms and must be placed
stable on firm and levelled ground.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense.
Do not operate the machine when
you are tired.
Do not operate the machine under
the influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Keep children and visitors a safe
distance from the work area.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Normal brushfire might ignite.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Wood dust is explosive and can also
represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like
beach and oak, is classified as a
carcinogenic substance.
Always use a suitable dust extraction
device
Before machining, remove any nails
and other foreign bodies from the
workpiece.
Specifications regarding the
maximum or minimum size of the
workpiece must be observed.
Do not force the power tool. It will do
a better and safer job and give you
much better service if it is used at the
rate for which it was designed.
Do not remove chips and workpiece
parts until the machine is at a
complete standstill.
Never operate with the guards not in
place – serious risk of injury!
Connection and repair work on the
electrical system may be carried out
by a qualified electrician only
Always unwind any extension cords
fully.
Damaged extension cords replace
immediately.
Do not use the power tool if the
ON/OFF switch does not turn the
power tool ON and OFF.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.
Do not use blades made from High
Speed Steel (HSS).
Remove defective saw blades
immediately.
Use carbide-tipped sawblades with a
negative chip angle only.
Never attempt to use ripping or
combination blades with this saw.
When cutting thin walled stock, it is
essential that you use a fine tooth
blade of at least 80 teeth.
A coarse blade may hook into the
stock and eject it.
This machine is not suitable for
cutting steel and other metals.
Never attempt to cut round or
irregular cross-section stock without
using a suitable jig.
If the blade stalls, switch off
immediately.
When using machine on a workstand,
always clamp it down.
Always listen to the machine and
switch off immediately if abnormal
sounds are heard.
Keep the slide lock tight unless slide
action is needed.
Ensure that the blade guard opens
and closes smoothly.
Always support long pieces with an
additional supporting stand of
appropriate height.
Never carry tool by operating handle.
Always use the carry handle or use
two hands to carry by the base.
Always use approved eye and ear
protection.
Keep hands away from blad at all
times.
Always unplug machine after use.
Summary of Contents for JSMS-10L
Page 10: ......