manualshive.com logo in svg

Jet JPJ-12B, Operating Instructions And Parts Manual

Share
Download
Jet JPJ-12B Operating Instructions And Parts Manual Download Page 7

7 

 

5.0

  Features and Terminology 

 

Figure 1 

6.0

  Receiving 

Carefully  unpack  the  machine  and  any  loose 
items  from  the  wood  case  and  inspect  for 
damage.  Any  damage  should  be  reported 
immediately  to  your  distributor  and  shipping 
agent.  Before  proceeding  further,  read  your 
manual  thoroughly  to  familiarize  yourself  with 
proper  assembly,  maintenance,  and  safety 
procedures. 

Remove  the  clear  plastic  protective  sheets  and 
remove the protective coating from the tables and 
cutterhead. This coating may be removed with a 
soft  cloth  moistened  with  kerosene.  Do  not  use 
acetone,  gasoline,  or  lacquer  thinner  for  this 
purpose. Do not use solvents on plastic parts. 

 

Use  care  when  cleaning  the 

cutterhead; the knives are very sharp. 

7.0

  Unpacking 

1.  Remove  all  contents  from  the  shipping 

carton. Do not discard the carton or packing 
material  until  the  machine  is  set  up  and 
running satisfactorily. 

2.  Inspect  the  contents  for  shipping  damage. 

Report damage, if any, to your distributor. 

This machine arrives fully  assembled.  However, 
some tools may be needed for adjustments. 

9.1

  Contents of Shipping Container 

1 

Planer/Jointer 

2 

Push blocks 

1 

6mm hex wrench 

1 

Aluminum knife gauge  

(JPJ-12B only)

 

2 

Star point screwdrivers  

(JPJ-12BHH only)

 

10  Knife inserts  

(JPJ-12BHH only)

 

10  Knife insert screws  

(JPJ-12BHH only)

 

1 

Owner's manual 

1 

Warranty card 

8.0

  Electrical Connection 

 

All  electrical  connections 

must  be  done  by  a  qualified  electrician.  All 
adjustments or repairs must be done with the 
machine  disconnected  from  the  power 
source,  unplugged.  Failure  to  comply  may 
result in serious injury!

 

The  model  JPJ-12B  and  JPJ-12BHH  Planer-
Jointer  is  rated  at  230V.  This  machine  is  not 
supplied with a plug. Use a plug and outlet rated 
at  least  30  amps.  The  circuit  for  the  machine 
should  also  be  protected  by  at  least  a  30-amp 
circuit breaker or fuse.  

Make sure the cutterhead rotates in the proper 
direction. 

If it does not, disconnect machine from 

power supply and reverse two of the phase wires 
on the supply input. 

Summary of Contents for JPJ-12B

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands