Jet JPJ-12B Operating Instructions And Parts Manual Download

Page: 17 / 48

Figure 19

10.8

Belt Replacement

Refer to Figures 20 - 22:

Preparation

To replace the

cutterhead drive belt

and/or the

planer feed-roller belt

, the jointer fence assembly

and two back panels must first be removed as
described below. A 4mm hex wrench, 5mm hex
wrench, and 17mm open wrench are required.

Disconnect machine from

power

source

before

making

any

adjustments. Failure to comply may cause
serious injury.

1. Disconnect machine from power source.

2. Remove four

button head socket screws

(B)

and the

jointer fence assembly

(A).

3. Remove two

button head socket scre

ws (D)

and the

upper back panel

(C).

4. Remove four

button head socket scre

ws (F)

and the

lower back panel

(E).

5. Loosen

top nut

(L) on the

tension adjustment

screw

(N), then turn the

bottom nut

(M) to

raise the

motor

(I) and create slack in

feed-

roller belt

(H) and

cutterhead drive belt

(G).

If there is still tension in feed-roller belt,
loosen two socket head cap screws attaching
gearbox to cabinet using a 5mm hex wrench.

6. Remove the

feed-roller belt

(H) from around

the

feed-roller pulley

(P) and

motor pulley

(K).

If the

cutterhead drive belt

(G) is to be replaced,

continue. Otherwise, proceed to step 10.

Cutterhead Drive Belt Replacement

Note:

If the

cutterhead drive belt

(G) is to be

replaced, steps 1 - 6 must be performed to
remove the

feed-roller belt

(H) before the

cutterhead drive belt can be replaced.

7. Remove

cutterhead drive belt

(G) from

around

cutterhead pulley

(O) and

pulley

(J).

8. Loop the new cutterhead drive belt around

the larger (inner)

motor pulley

(J) and

cutterhead pulley

(O).

If the

feed-roller belt

(H) is to be replaced as well,

proceed to step 10. Otherwise, continue.

9. Loop the original

feed-roller belt

(H) around

the smaller (outer)

motor pulley

(K) and

feed-

roller pulley

(P).

Proceed to step 11.

Feed-Roller Belt Replacement

10. Loop the new feed-roller belt around the

smaller (outer)

motor pulley

(K) and

feed-

roller pulley

(P).

Concluding Steps

11. Turn

bottom nut

(M) on

tension adjustment

screw

(N) to lower the

motor

(I) and create

tension in

feed-roller belt

(H) and

cutterhead

drive belt

(G), then tighten the

top nut

(L).

If the gearbox was adjusted in step 5,
reposition the gearbox to maintain tension on
the feed-roller belt and tighten the two socket
head cap screws.

12. Replace the

lower back panel

(E),

upper back

panel

(C), and

jointer fence assembly

(A) with

their respective screws.

Figure 20

Summary of Contents for JPJ-12B

















































Search results

Summary of Contents for JPJ-12B

Reviews:

Related manuals for JPJ-12B

Brands by name

Popular brands

Jet JPJ-12B, Operating Instructions And Parts Manual

Search results

Summary of Contents for JPJ-12B

Reviews:

Related manuals for JPJ-12B

Brands by name

Popular brands