manualshive.com logo in svg

Jet JPJ-12B, Operating Instructions And Parts Manual

Share
Download
Jet JPJ-12B Operating Instructions And Parts Manual Download Page 35

35 

 

15.8

  Planer Table Assembly 

– Parts List 

Index No.  Part No. 

Description 

Size 

Qty

 

1 ............... JPJ12B-401 ............. Socket Head Button Screw .................................. M4 x 0.7P x 8L ............ 8 
2 ............... JPJ12B-402 ............. Cover ....................................................................  .................................... 4 
3 ............... JPJ12B-403 ............. Dust-Proof Felt Pad .............................................  .................................... 4 
4 ............... JPJ12B-404 ............. Nut for Drive Lead Screw .....................................  .................................... 1 
5 ............... JPJ12B-405 ............. O-Ring .................................................................. G63 ............................. 4 
6 ............... JPJ12B-406 ............. Thrust Bearing .....................................................  .................................... 8 
7 ............... JPJ12B-407 ............. Lead Screw Hub ..................................................  .................................... 4 
8 ............... JPJ12B-408 ............. Sprocket ...............................................................  .................................... 4 
9 ............... JPJ12B-409 ............. Bevel Gear ...........................................................  .................................... 1 
10 ............. JPJ12B-410 ............. Star Washer .........................................................  .................................... 4 
11 ............. JPJ12B-411 ............. Lock Nut ...............................................................  .................................... 4 
12 ............. JPJ12B-412 ............. Key ....................................................................... 3 x 3 x 10 .................... 4 
13 ............. JPJ12B-413 ............. Key ....................................................................... 4 x 4 x 12 .................... 1 
14 ............. JPJ12B-414 ............. Shoulder Screw ....................................................  .................................... 8 
15 ............. TS-1541021 ............. Nylon Lock Nut ..................................................... M6 x 1.0P .................... 8 
16 ............. JPJ12B-416 ............. External Retaining Ring, C-Type ......................... STW-35 ....................... 1 
18 ............. JPJ12B-418 ............. Planer Table .........................................................  .................................... 1 
19 ............. TS-2311081 ............. Hex Nut ................................................................ M8 x 1.25P .................. 1 
20 ............. TS-1490091 ............. Hex Cap Screw .................................................... M8 x 1.25P x 50L ........ 1 
21 ............. JPJ12B-421 ............. Lead Screw ..........................................................  .................................... 4 
22 ............. TS-1550071 ............. Flat Washer .......................................................... 11 x 37 x 3.0T ............. 1 
23 ............. TS-1551071 ............. Lock Washer ........................................................ M10 ............................. 1 
24 ............. TS-1505021 ............. Socket Head Cap Screw  ..................................... M10 x 1.5P x 20L ........ 5 
25 ............. JPJ12B-425 ............. Nut for Driven Lead Screw ...................................  .................................... 3 
26 ............. JPJ12B-426 ............. Pointer ..................................................................  .................................... 1 
27 ............. JPJ12B-427 ............. Phillips Pan Head Machined Screw ..................... M5 x 0.8P x 6L ............ 2 
28 ............. JPJ12B-428 ............. Chain .................................................................... Z410 x 126P ............... 1 

 

 

 

Summary of Contents for JPJ-12B

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands