Jet JJ-8CS Operating Instructions And Parts Manual Download Page 3

Page: 3 / 32

Table of Contents

Warranty and Service .............................................................................................................................. 2

Table of Contents .................................................................................................................................... 3

Warning................................................................................................................................................... 4

Introduction ............................................................................................................................................. 5

Levers and Controls ................................................................................................................................ 6

Specifications .......................................................................................................................................... 6

Unpacking and Cleanup .......................................................................................................................... 7

Unpacking and Cleanup ....................................................................................................................... 7

Installing Bed to Stand ......................................................................................................................... 8

Installing Pedestal Switch

(JJ-8HH only)

.............................................................................................. 8

Installing Handwheels .......................................................................................................................... 9

Assembling Knife-Setting Gauge

(JJ-8CS only)

.................................................................................... 9

Installing V-Belts .................................................................................................................................. 9

Installing Cutterhead Guard................................................................................................................ 10

Installing Access Door........................................................................................................................ 10

Installing Dust Chute.......................................................................................................................... 10

Electrical Connections........................................................................................................................ 10

Extension Cords................................................................................................................................. 11

Adjustments .......................................................................................................................................... 11

90° Fence Adjustment........................................................................................................................ 11

45° Fence Adjustment........................................................................................................................ 12

Leveling Outfeed Table to Cutterhead Knives.................................................................................... 12

Removing and Replacing Knives

(JJ-8CS only)

.................................................................................. 14

Replacing or Rotating Knife Inserts

(JJ-8HH only)

.............................................................................. 14

Gib Adjustment .................................................................................................................................. 15

Operation .............................................................................................................................................. 15

Jointing Warped Material.................................................................................................................... 16

Direction of Grain............................................................................................................................... 16

Bevel Cut........................................................................................................................................... 16

Taper Cut........................................................................................................................................... 17

Rabbet Cut ........................................................................................................................................ 17

Maintenance.......................................................................................................................................... 18

Lubrication ......................................................................................................................................... 18

Blade Care......................................................................................................................................... 18

Sharpening the Knives

(JJ-8CS only)

................................................................................................. 18

Cutterhead Removal .......................................................................................................................... 18

Replacement Parts ................................................................................................................................ 20

Fence Assembly (all models) ............................................................................................................. 21

Parts List – Fence Assembly (all models) ........................................................................................... 21

Bed Assembly (all models) ................................................................................................................. 22

Parts List – Bed Assembly (all models)............................................................................................... 23

Stand and Motor Assembly (JJ-8CS only) .......................................................................................... 24

Parts List – Stand and Motor Assembly (JJ-8CS only) ........................................................................ 25

Stand and Motor Assembly (JJ-8HH only) .......................................................................................... 26

Parts List – Stand and Motor Assembly (JJ-8HH only)........................................................................ 27

Parts List – Cutterhead Assembly (JJ-8CS only)................................................................................. 28

Parts List – Cutterhead Assembly (JJ-8HH only) ................................................................................ 29

Electrical Connections (JJ-8CS only).................................................................................................. 30

Electrical Connections (JJ-8HH only).................................................................................................. 31

Summary of Contents for JJ-8CS

































Search results

Summary of Contents for JJ-8CS

Reviews:

Related manuals for JJ-8CS

Brands by name

Popular brands

Jet JJ-8CS, Operating Instructions And Parts Manual

Search results

Summary of Contents for JJ-8CS

Reviews:

Related manuals for JJ-8CS

Brands by name

Popular brands