Jet JCDC-3 Operating Instructions And Parts Manual Download Page 3

 

3

24.  Do not use to pick up anything that is burning or 

smoking, such as cigarettes, matches or hot 
ashes. 

25.  Do not use to pick up flammable or combustible 

liquids such as gasoline, or use in areas where 
they may be present. 

26. Do not pull or carry by cord, use cord as a 

handle, close a door on cord, or pull cord 
around sharp edges or corners. Do not run dust 
collector over cord. Keep cord away from 
heated surfaces. 

27.  Do not use this dust collector with a damaged 

cord or plug. If the unit is not working as it 
should, has been dropped, damaged, left 
outdoors, or dropped into water, return it to a 
service center. 

28. Do not unplug by pulling on cord. To unplug, 

grasp the plug, not the cord. 

29. Do not use without dust bag and/or filters in 

place. 

30.  Do not handle plug or machine with wet hands. 

31.  Do not put any objects into the openings. Do not 

use with any opening blocked; keep free of 

dust, lint, hair, and anything that may reduce air 
flow. 

32.  Do not operate without hose connected to the 

inlet. Place cap on unused inlet port. Hazardous 
moving parts inside. Unplug before removing or 
connecting inlet or inlet guard. 

33. 

Use recommended accessories; improper 
accessories may be hazardous. 

34.  Maintain tools with care. Follow instructions for 

lubricating and changing accessories. 

35. Turn off machine and disconnect from power 

before cleaning. Use a brush or compressed air 
to remove chips or debris; do not use bare 
hands. 

36.  Do not leave the machine when it is plugged in. 

Unplug from outlet when not in use and before 
servicing. 

37. Do not stand on the machine. Serious injury 

could occur if the machine tips over. 

38. The dust collector is intended for household 

use. 

Familiarize yourself with the following safety notices used in this manual: 

 This means that if precautions are not heeded, it may result in minor injury and/or possible 

machine damage. 

 This means that if precautions are not heeded, it may result in serious, or possibly even fatal, 

injury. 

SAVE THESE INSTRUCTIONS 

 

2.0

  About this manual 

This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model 
JCDC-3 Cyclone Dust Collector. This manual contains instructions on installation, safety precautions, general 
operating procedures, maintenance instructions and parts breakdown. Your machine has been designed and 
constructed to provide consistent, long-term operation if used in accordance with the instructions as set forth in 
this document.  

This manual is not intended to be an exhaustive guide to dust removal strategies, installation of shop duct work, 
or the use of optional dust collection accessories. Additional knowledge may be obtained from experienced users 
or trade articles. Whatever accepted methods are used, always make personal safety a priority. 

If there are questions or comments about this product, please contact your local supplier or JET. JET can also 
be reached at our web site: www.jettools.com. 

Retain this manual for future reference. If the machine transfers ownership, the manual should accompany it. 

 

 

 

Summary of Contents for JCDC-3





















Reviews: