background image

 

2

Warranty and Service 

JET, Wilton and Powermatic warrants every product they sell against manufacturers’ defects. If one of our tools needs service 
or repair, please contact

 

Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. 

Warranty Period

 

The general warranty lasts for the time period specified in the literature included with your product or on the official JET, Wilton 
or Powermatic branded websites.  

 

JET, Wilton and Powermatic products carry a limited warranty which varies in duration based upon the product. (See 
chart below) 

 

Accessories carry a limited warranty of one year from the date of receipt. 

 

Consumable items are defined as expendable parts or accessories expected to become inoperable within a 
reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects. 

Who is Covered 

This warranty covers only the initial purchaser of the product from the date of delivery. 

What is Covered 

This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty does not 
cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, 
alterations or lack of maintenance. 

Warranty Limitations 

Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a Two Year 
Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.

 

How to Get Technical Support 

Please contact Technical Service by calling 1-800-274-6846. 

Please note that you will be asked to provide proof of initial 

purchase when calling. 

If a product requires further inspection, the Technical Service representative will explain and assist 

with any additional action needed.

 

JET, Wilton and Powermatic have Authorized Service Centers located throughout the 

United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service Center 
Locator on the JET, Wilton or Powermatic website.

 

More Information 

JET, Wilton and Powermatic are consistently adding new products. For complete, up-to-date product information, check with 
your local distributor or visit the JET, Wilton or Powermatic website. 

How State Law Applies 

This warranty gives you specific legal rights, subject to applicable state law.  

Limitations on This Warranty 

JET, WILTON AND POWERMATIC LIMIT ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY 
FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW 
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. 
JET, WILTON AND POWERMATIC SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR 
PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE 
USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. 
JET, Wilton and Powermatic sell through distributors only. The specifications listed in JET, Wilton and Powermatic printed 
materials and on official JET, Wilton and Powermatic-branded websites are given as general information and are not binding. 
JET, Wilton and Powermatic reserve the right to effect at any time, without prior notice, those alterations to parts, fittings, and 
accessory equipment which they may deem necessary for any reason whatsoever. JET

®

 branded products are not sold in 

Canada by Walter Meier Manufacturing Americas. 
 

Product Listing with Warranty Period  

90 Days – Parts; Consumable items; Light-Duty Air Tools 
1 Year – Motors; Machine Accessories; Heavy-Duty Air Tools; Pro-Duty Air Tools 
2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories 
5 Year – Woodworking Machinery 
Limited Lifetime – Wilton branded products; JET Parallel clamps; Manual Hoists; Manual Hoist Accessories; 
Shop Tools; Warehouse & Dock products; Hand Tools 

 
NOTE:  JET, Wilton and Powermatic are divisions of Walter Meier Manufacturing Americas.  References in this document to 
JET, Wilton and/or Powermatic also apply to Walter Meier Manufacturing Americas or any of its successors in interest to the 
JET, Wilton and/or Powermatic brands. 

Summary of Contents for J- A5818

























Reviews: