5
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in off position
before plugging in.
17.
USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the cutting
tool is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further
use of the tool, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function - check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade
or cutter against the direction of rotation of the
blade or cutter only.
21.
NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER OFF. Don’t
leave tool until it comes to a complete stop.
22.
DO NOT REMOVE JAMMED CUTOFF
PIECES until the blade has stopped.
23. MAINTAIN PROPER ADJUSTMENT of blade
tension, blade guides and thrust bearings.
24. ADJUST UPPER BLADE GUIDE TO JUST
CLEARWORKPIECE.
25.
HOLD WORKPIECE FIRMLY AGAINST
TABLE.
General Electrical Cautions
This saw should be grounded in accordance with the National Electrical Code and local codes and ordinances.
This work should be done by a qualified electrician. The saw should be grounded to protect the user from
electrical shock.
Caution:
For circuits which are far away from the electrical service box, the wire size must be increased in
order to deliver ample voltage to the motor. To minimize power losses and to prevent motor overheating and
burnout, the use of wire sizes for branch circuits or electrical extension cords according to the following table is
recommended.
Ampere Rating
Volts
Total length of cord in feet
120 V
25 ft.
50 ft.
100 ft.
150 ft.
240 V
50 ft.
100 ft.
200 ft.
300 ft.
More than
Not more than
AWG minimum gage
0 6
18 16 16
14
6 10
18 16 14
12
10 12
16 16 14
12
12 16
14
12
Not
recommended
Only the applicable parts of the Table need to be included. For instance, a 120-volt product need not include the 240-volt heading.
Switch Padlock
To safeguard your machine from unauthorized
operation and to avoid accidental starting by young
children, the use of a padlock (not provided) is
highly recommended.
To lock the main switch in the OFF position,
remove the switch key from the switch. Place the
key in a location that is inaccessible to children and
others not qualified to use the tool.
1. Open the padlock (Fig. A).
2. Insert through holes in the start button (Fig. B).
3. Close
the
padlock.
4. Place the key in a safe place and out of reach
of children.
For three phase tools without the lock-off feature,
observe the following instruction: The installer shall
follow local regulations and National Electrical
Code, ANSI/NFPA 70 installation requirements.
Summary of Contents for J-8201
