Jet 718200K Operating Instructions And Parts Manual Download Page 3

Page: 3 / 32

Table of Contents

Warranty and Service .................................................................................................................................... 2

Table of Contents .......................................................................................................................................... 3

Warning ......................................................................................................................................................... 4

Introduction ................................................................................................................................................... 5

Levers and Controls ...................................................................................................................................... 6

Specifications ................................................................................................................................................ 6

Setup and Assembly ..................................................................................................................................... 7

Unpacking and Cleanup ............................................................................................................................ 7

Installing Bed to Stand............................................................................................................................... 8

Installing Pedestal Switch

(JWJ-8HH only)

............................................................................................... 8

Installing Handwheels ................................................................................................................................ 9

Assembling Knife-Setting Gauge

(JWJ-8CS only)

.................................................................................... 9

Installing V-Belts ........................................................................................................................................ 9

Installing Cutterhead Guard .................................................................................................................... 10

Installing Access Door ............................................................................................................................. 10

Installing Dust Chute ............................................................................................................................... 11

Electrical Connections ............................................................................................................................. 11

Extension Cords ...................................................................................................................................... 11

Adjustments ................................................................................................................................................ 12

90° Fence Adjustment ............................................................................................................................. 12

45° Fence Adjustment ............................................................................................................................. 12

Leveling Outfeed Table to Cutterhead Knives ........................................................................................ 13

Removing and Replacing Knives

(JWJ-8CS only)

.................................................................................. 14

Replacing or Rotating Knife Inserts

(JWJ-8HH only)

.............................................................................. 15

Infeed Table Depth Stop ......................................................................................................................... 16

Gib Adjustment ........................................................................................................................................ 16

Operation..................................................................................................................................................... 16

Jointing Warped Material ......................................................................................................................... 17

Direction of Grain ..................................................................................................................................... 17

Bevel Cut ................................................................................................................................................. 18

Taper Cut ................................................................................................................................................. 18

Rabbet Cut .............................................................................................................................................. 18

Maintenance ................................................................................................................................................ 19

Lubrication ............................................................................................................................................... 19

Blade Care ............................................................................................................................................... 19

Sharpening Knives

(JWJ-8CS only)

........................................................................................................ 19

Cutterhead Removal ................................................................................................................................ 19

Replacement Parts ...................................................................................................................................... 20

Fence Assembly (all models) .................................................................................................................. 21

Parts List – Fence Assembly (all models) ............................................................................................... 21

Bed Assembly (all models) ...................................................................................................................... 22

Parts List – Bed Assembly (all models) ................................................................................................... 23

Stand and Motor Assembly (JWJ-8CS only) ........................................................................................... 24

Parts List – Stand and Motor Assembly (JWJ-8CS only) ........................................................................ 25

Stand and Motor Assembly (JWJ-8HH only) ........................................................................................... 26

Parts List – Stand and Motor Assembly (JWJ-8HH only) ........................................................................ 27

Parts List – Cutterhead Assembly (JWJ-8CS only) ................................................................................. 28

Parts List – Cutterhead Assembly (JWJ-8HH only) ................................................................................ 29

Electrical Connections (JWJ-8CS only) ................................................................................................... 29

Electrical Connections (JWJ-8HH only) .................................................................................................. 31

Summary of Contents for 718200K

































Search results

Summary of Contents for 718200K

Reviews:

Related manuals for 718200K

Brands by name

Popular brands

Jet 718200K, Operating Instructions And Parts Manual

Search results

Summary of Contents for 718200K

Reviews:

Related manuals for 718200K

Brands by name

Popular brands